AltIMU-10 v5 - gyroscope, accelerometer, compass and I2C 3-5V altimeter - Pololu 2739

Index: PLL-05728 EAN: 5903351240413

Sensor for measuring acceleration, magnetic field, angular speed and altitude. It is a combination of 3-axis accelerometer and gyroscope LSM6DS33, LIS3MDL magnetometer and barometer LPS25H. Communicates via the I2C bus.

 

AltIMU-10 v5 - gyroscope, accelerometer, compass and I2C 3-5V altimeter - Pololu 2739
€42.50
€34.55 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Description of product: AltIMU-10 v5 - gyroscope, accelerometer, compass and I2C 3-5V altimeter - Pololu 2739

Module AltIMU-10 v5 is the 3-axis sensors: accelerometer, gyroscope LSM6DS33, magnetometer LIS3MDL, andLPS25H barometer. Using these sensors, it is possible to create a complete system AHRS (attitude and heading reference system), i.e. to determine the position of the object in three-dimensional space. Data from the barometer can be easily converted to the height, thanks to gyroscope, you can track the rotations of the object, and accelerometer, along with magnetometer offset the drift of the gyroscope and determine the irrespective reference point.

The kit includesconnectors goldpin raster of 2.54mm for self-soldering.

Specification

  • Supply voltage: 2.5 V - 5.5 V
  • Current consumption: 6 mA
  • Three axes: X, Y, Z
  • Communication interface: I2C (TWI)
  • Data format:
    • Accelerometer: 16-bits per axis (left-aligned)
    • Gyroscope: 16-bit per axis
    • Magnetometer:16-bits per axis (left-aligned)
    • Barometer: 24-bit (4096 LSb/mbar)
  • Measuring ranges (configurable):
    • Accelerometer: ± 2, ± 4, ± 8, ± 16 g
    • Gyroscope: ± 125, ± 245, ± 500, ± 1000, ± 2000 °/s
    • Barometer: 26 kPa to 126 kPa
    • Magnetometer: ± 4, ± 8, ± 12, ± 16 gauss
  • Size: 25 x 13 x 3 mm
  • Weight: 0.8 g (without connectors)

 

  The module has a voltage regulator and all necessary passive components. The leads are popular goldpin connectors for connecting the sensor viawiresor to connect directly to breadboard.

Compared tothe board MinImu v5 that has no height sensor.

 

In relation to the previous version, AltIMU-10 v5 has a new 3-axis MEMS sensors from the company ST - gyroscope and accelerometer LSM6DS33 (documentation), and magnetometer LIS3MDL (documentation). These sensors have higher precision and more improved stability of measurement than its predecessors. New magnetometer allows to measure in a wider range - up to 16 gauss. The distribution of leads is fully compatible with the version v4, while changed were sample programs and libraries for Arduino.

 

AltIMU-10 v5 is pin-compatible withthe module MinIMU-9 v5. It has the same functions with the expansion with digital barometer that can be used as a height sensor. Properly written code for the MinIMU-9 v5 will work with the system AltIMU-10 v5.

 

The product is compatible with Arduino

A library for user of the moduleArduino:

 

.

Leads

The sensor has five leads for mounting goldpin connectors - 2.54 mm pitch (included).

 

Wyprowadzenia modułu IMU  3D

 

PIN Description
SCL Clock line of the I2C bus. High state is equal to the voltage VIN. Low GND.
Traffic The data line of the I2C bus. High state is equal to the voltage VIN. Low GND.
GND The potential of mass of the system.
VIN Supply voltage from 2.5 V to 5.5 V
VDD In the case where the voltage is higher than 3.3 V, the lead can be the output voltage of 3.3 V with current efficiency up to 150 mA. When the supply voltage is in the range of 2.5 V - 3.3 V, you should connect it to the VDD lead.
SA0

Input to change I2C addresses in accordance with the table below.

Pin works with a voltage of 3.3 V,connecting5 V can permanently damage the chip.

 I2C addresses

Accelerometer, magnetometer, gyroscope and barometer, in a module, have the 7-bit addresses. Installed are respectively:

 

Sensor

Address

by default

Address

SA0 in low state

LSM6DS33

accelerometer and gyroscope

1101011b 1101010b

LIS3MDL

magnetometer

0011110b 0011100b

LPS25H

barometer

1011101b 1011100b
 

The bus operates properly with a clock frequency up to 400 MHz (fast mode).

 

Tips for first use

All the necessary information about the connection and the maintenance of the sensors of the module AltIMU-10 are in the documentation of theindividual sensors. Below are several the most important facts:

  • Pressure sensor, accelerometer and gyroscope are disabled by default. You have to run them by setting the appropriate bits in the appropriate registers.
  • Possible is multi-read and multi-record of the accelerometer, gyroscope and barometer with one command of I2C via setting the most significant bit of the address (starting autoincrementing).

  

 

Package width 7.5 cm
Package height 0.5 cm
Package depth 8.5 cm
Package weight 0.003 kg

Be the first to ask a question about this product!

Product reviews

AltIMU-10 v5 - gyroscope, accelerometer, compass and I2C 3-5V altimeter - Pololu 2739

5/5

Average grade

1

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Zdjęcia użytkowników

Customers who bought this product also bought:

Products from the same category: