0.95inch RGB OLED (A) IC Test Board
0.95inch RGB OLED (A) IC Test Board
0.95inch RGB OLED (A) IC Test Board
0.95inch RGB OLED (A) IC Test Board - zdjęcie 1
0.95inch RGB OLED (A) IC Test Board - zdjęcie 2
0.95inch RGB OLED (A) IC Test Board - zdjęcie 3

ArduCam-Mini OV5642 5MPx 2592x1944px 120fps SPI - camera module for Arduino

Index: ACM-06558
BOTLAND B. DERKACZ SPÓŁKA JAWNA Opinie z ekomi-pl.com

Camera module for Arduino 5 MPx with a resolution of 2592 px x 1944 and speeds up to 120 frames per second. It extends the capabilities of the microcontroller with the ability to shoot photos and record videos. The device operates with a voltage of 3.3 V and 5 V, it communicates via SPI, the angle of view - 24 ° (non-linear), the lens is 1/4".

€50.00
€40.65 tax excl.

In stock, shipping 24 hours!
(Check quantity)
Shipping in 24 hours
30-day returns
PayPal payment
Manufacturer: ArduCam
Compatibility: Arduino

Description

Camera module for Arduino 5 MPx with a resolution of 2592 px x 1944 and speeds up to 120 frames per second. It extends the capabilities of the system, for example, microcontrollers Arduino, STM32 and mini-computers Raspberry Pi, with the possibility of taking photos and recording video clips. The device operates with a voltage of 3.3 V and 5 V, it communicates via SPI, the angle of view - 24 ° (non-linear), the lens is 1/4".

Kamera ArduCam 5MPx do Arduino

Modes of operation

  • Single Capture Mode - the default mode of the device after the indicating the command via SPI, the camera captures a frame and adds it to the buffer, while setting a flag in the registry. By checking the state of the flag, the user knows that the read has been completed.
  • Multiple Capture Mode - an advanced mode where the user specifies the number of frames to be captured. Please note that the number of frames cannot exceed the capacity of the buffer.
  • JPEG Compression - in this mode, the output are compressed data in the JPG format with higher resolution, than RGB.
  • Normal Read and Burst Read Operation - in this mode, it is sufficient to send a read command for receiving the continuous transmission of frames via an SPI interface.
  • Rewind the Read Operation - it allows to read, several times, the same data contained in the buffer.
  • Low Power Mode - disables the sensor and transducer in order to save energy.
  • Image Sensor Control - mode change parameters of the camera sensor, i.a. balance, brightness, contrast and saturation.

The product is compatible with Arduino

A user manual and library for Arduino are available in GitHub.

Block diagram

The device consists of a lens, sensor and electronic components with the data buffer and the controller of the SPI bus. The user has also access directly to the sensor via the I2C bus.

ArduCam-Mini OV2640

A block diagram of the camera module ArduCAM-Mini.

Specification

  • Working voltage: 3.3 V / 5 V
  • Maximum resolution: 2592 px x 1944 (5 MPx)
  • The number of frames per second:
    • up to 120 FRAMES per second for the format of QVGA (320x240px)
    • up to 60 FRAMES per second for VGA 640x480px)
    • up to 60 fps for 720p (1280c720px)
    • up to 30 FRAMES per second for 1080p (1920x1080px)
    • up to 15 FRAMES per second for 5 MPx (2592x1944px)
  • Lens size: 1/4 "
  • Lens mounting: CS-mount / M12
  • Pixel size: 1.4 µm x 1.4
  • Range of image: 3673,6 x 2738,4 µm
  • Angle of view: 24 ° (non-linear)
  • Output formats:
    • 422/420 YUV / YCbCr 422
    • RGB565/555/444, CCIR656
    • compressed 8-bit data 
    • 8 / 10-bit RAW RGB Data
  • Configuration of sensor through I2C bus
  • Module dimensions: 35 × 25 mm

The details in the technical documentation of the sensor OV5642.

Pins

The device has soldered the 8 pin connector, pitch of 2.54 mm.

ArduCam-Mini  - podłączenie

Pin Name Description
1 CS Chip Select - selects a device on the SPI bus, activated by low state.
2 MOSI Data output line of SPI bus.
3 MISO Data output line of SPI bus.
4 SCLK Clock line of the SPI bus.
5 GND The ground of the system.
6 5V Supply voltage from 3.3 V to 5 V
7 SDA Data output line of I2C bus.
8 SCL Clock line of the I2C bus.

Interface SPI / I2C
Resolution 2592x1944px
Camera - matrix OV5642
Camera - lens CS-mount / M12
Camera - format 1/4 ''
Camera - type module

Same-day shipping

  • Crediting the payment for the order on our account on a business day before 10:00 AM means sending the goods on the same day.
  • All packages are being delivered by GLS Group courier and covered with insurance up to 1200 EUR.
  • You will receive a link to track your package and monitor the progress of delivery as soon as it is shipped.

Terms of delivery 

GLS - zone 1

Austria, Belgium, Croatia, The Czech Republic, Denmark, Germany, Netherlands, Poland, Slovakia 

  • Delivery time: 2-4 days
  • Delivery cost: from 4.18 EUR
  • Insurance: 1200 EUR
GLS - zone 2

Bulgaria, Estonia, France, Hungary, Italy, Latvia, Lithuania, Luxembourg, Portugal, Romania, San Marino, Slovenia

  • Delivery time: 2-5 days
  • Delivery cost: from 5.35 EUR
  • Insurance: 1200 EUR
GLS - zone 3

Cyprus, Finland, Greece, Ireland, Lichtenstein, Malta, Spain, Sweden 

  • Delivery time: 2-7 days
  • Delivery cost: from 7.67 EUR
  • Insurance: 1200 EUR

Payment methods

Card image cap
PayPal
  • Botland is a PayPal verified seller. Protect your financial information with this fast, safe and secure online payment system.

Card image cap
PayU
  • Choose easy and quick PayU e-payment method. Your financial information will stay secure.

Customers who bought this product also bought:

Servo Motor Shield v2.3 - 2-channel motor driver, stepper motors and servos - Adafruit 1438

Cap for Arduino to control four DC motors (13.5 V/1.2 A), two stepper motors and two servos. It communicates through interface I2, using only two lines of Arduino.
Index: ADA-02444
Index: ADA-02444
Waiting time: approx. 10-30 days
Regular price €26.74 Price €26.74

Motor Control Shield - 4-channel motor driver 9V/0.6A - Shield for Arduino - Waveshare 9724

The module allows you to control four DC motors or two stepper motors using Arduino kits. The system allows you to adjust the direction and speed of rotation of the motors...
Index: WSR-04914
Index: WSR-04914
In stock, shipping 24 hours!
(Check quantity)
Regular price €7.88 Price €7.88

Arduino Motor Shield Rev3

Module allows control of two DC motors (DC) using Arduino kits. The system allows you to adjust the direction and speed of rotation of DC motors with a current consumption up...
Index: ARD-01215
Index: ARD-01215
In stock, shipping 24 hours!
(Check quantity)
Regular price €24.42 Price €24.42

DC Motor 37Dx73L with 131:1 Gear 12V 80RPM + encoder CPR 64

Geared motor 131:1, 80 rpm, torque 18 kg*cm (1.79 Nm). The device has a quadrature encoder with a resolution of 64 pulses per revolution (after translating 8400 pulses per...
Index: PLL-05114
Index: PLL-05114
Unavailable
Regular price €36.98 Price €36.98

DFRduino Uno v3 - compatible with Arduino

DFRobot module fully compatible with Arduino Uno R3. It has 14 digital inputs/outputs, 6 PWM channels, 6 analog inputs and popular communication interfaces. Colored connectors...
Index: DFR-02683
Index: DFR-02683
Available, 24h shipping!
(Check quantity)
Regular price €11.60 Price €11.60

Romeo v2 ATmega32u4 - all in one controller - compatible with Arduino

DFRobot module compatible with Arduino Leonardo. In addition to the traditional features of this type of board has a connector for XBee modules, a two-channel 32V/2A motor...
Index: DFR-02688
Index: DFR-02688
Available, 24h shipping!
(Check quantity)
Regular price €30.21 Price €30.21

Raspberry Pi tape - camera 200cm 15 wires 1mm raster

Tape with a length of 200 cm connecting the minicomputer Raspberry Pi with the dedicated camera. The connector has 15 veins, pitch is 1 mm.
Index: ODS-03952
Index: ODS-03952
In stock, shipping 24 hours!
(Check quantity)
Regular price €1.37 Price €1.37

Laser diode 5mW red 650nm 5V

The module with a laser emitting light in a red color. Power equal to 5 MW. Voltage supply from 3 to 5 V.
Index: LED-06450
Index: LED-06450
In stock, shipping 24 hours!
(Check quantity)
Regular price €0.63 Price €0.63

Stepper Motor JK42HM48-1684 400 steps 3,0V/1,68A/0,43Nm

Bipolar stepper motor , four-wire. Has a resolution of 400 steps per revolution (0.9 degree). Powered by 3.0 V, draws 1680 mA per coil. Torque is 4.4 kg*cm (0.43 Nm)....
Index: MOT-03606
Index: MOT-03606
Available, 24h shipping!
(Check quantity)
Regular price €22.09 Price €22.09

Big StarterKit for Arduino - 47 elements

A set of electronic components that will help you get started with modules from the Arduino. Included are more than 45 items, including: LEDs, resistors, various sensors,...
Index: ARD-05413
Index: ARD-05413
Waiting time: approx. 10-30 days
Regular price €81.37 Price €81.37

Arduino Uno Rev3 - module A000066

The original module from the Arduino® Uno with the AVR microcontroller ATmega328 in an interchangeable housing. It has 32 KB Flash memory, 2 KB RAM, 14 digital I/o of which...
Index: ARD-01060
Index: ARD-01060
In stock, shipping 24 hours!
(Check quantity)
Regular price €22.09 Price €22.09

Power supply 12V/2,5A - 100V-230V - DC plug 5,5/2,1mm

Stabilized power supply. Supply voltage: 100 V to 230 V. Output voltage: 12 V DC. Output current: 2.5 A. Connector: DC 5.5 / 2.1 m plug.
Index: ZAS-02999
Index: ZAS-02999
Waiting time: about 10-30 days
Regular price €4.63 Price €4.63

Products from the same category

Raspberry Pi Camera HD v2 8MPx - original camera for Raspberry Pi

The second version of the popular camera connected to a special minicomputer Raspberry Pi connector, version4, 3, 2, B+. The device has a matrix with a resolution of 8 Mpx,...
Index: RPI-06124
Index: RPI-06124
In stock, shipping 24 hours!
(Check quantity)
Regular price €31.40 Price €31.40

Camera HD G camera OV5647 5Mpx - wide-angle - for Raspberry Pi - Waveshare 10344

The module with a wide-angle camera (160°) connects to the dedicated Raspberry Pi mini-computer connector in versions 3, 2, B+, A+ and older A and B. The device has a 1/4 " CCD...
Index: WSR-04524
Index: WSR-04524
Available, 24h shipping!
(Check quantity)
Regular price €22.77 Price €22.77

Raspberry Pi NoIR Camera HD v2 8MPx - original night camera for Raspberry Pi

Module with the camera, sensitive to infrared light for Raspberry Pi minicomputer version 3, 2, B+. The device has a matrix with a resolution of 8 Mpx, supports HD mode, 1080p,...
Index: RPI-06128
Index: RPI-06128
In stock, shipping 24 hours!
(Check quantity)
Regular price €30.21 Price €30.21

Camera HD D OV5647 5Mpx camera - for Raspberry Pi - Waveshare 11297

Camera module with OV5647 sensor, connected to a special connector of minicomputer Raspberry Pi, version 3, 2, B+, A+ and older A and B. The device has a matrix CCD 1/4" with...
Index: WSR-05620
Index: WSR-05620
In stock, shipping 24 hours!
(Check quantity)
Regular price €16.26 Price €16.26

Camera HD B OV5647 5Mpx - with focus adjustment for Raspberry Pi - Waveshare 8193

Camera module with adjustable focus, connected to the appropriate connector of minicomputer Raspberry Pi, version 3, 2, B+, A+ and older A and B. The device has a matrix CCD...
Index: WSR-04471
Index: WSR-04471
Czas oczekiwania: ok. 10-30 dni
Regular price €15.56 Price €15.56

OdSeven Camera HD camera OV5647 5Mpx - for Raspberry Pi

Camera module with OV5647 sensor connected to a corresponding connector on a minicomputer Raspberry Pi in versions 4B, 3B+, 3B, 3, 2, B+, A+ and above A and B. The device has a...
Index: ODS-05619
Index: ODS-05619
In stock, shipping 24 hours!
(Check quantity)
Regular price €5.56 Price €5.56

Camera HD Night Vision H OV5647 5Mpx - wide angle IR for Raspberry Pi + IR modules - Waveshare 10703

Module with wide angle camera (160 °) is connected to the selected connector of minicomputer Raspberry Pi version 3, 2, B+, A+ and older A and B. The device has a matrix CCD...
Index: WSR-04523
Index: WSR-04523
In stock, shipping 24 hours!
(Check quantity)
Regular price €28.81 Price €28.81

Camera HD F Night Vision OV5647 5Mpx - IR with focus adjustment for Raspberry Pi + IR modules - Waveshare 10299

Camera module with adjustable focus connected to the special connector of minicomputer Raspberry Pi version 3, 2, B+, A+ and older A and B. The device has a matrix CCD 1/4"...
Index: WSR-04521
Index: WSR-04521
In stock, shipping 24 hours!
(Check quantity)
Regular price €19.28 Price €19.28

CSI / DSI Extender Thingy for Raspberry Pi camera/display tapes - Adafruit 3671

The board is a great tool that allows you to extend the tape 15-pin pitch of 1 mm CSI for camera or DSI display Raspberry Pi.
Index: ADA-10318
Index: ADA-10318
In stock, shipping 24 hours!
(Check quantity)
Regular price €3.93 Price €3.93

Camera Raspberry Pi HQ IMX477R 12,3 MPx for Raspberry Pi

High quality camera for Raspberry Pi with higher resolution and frequency than the official Raspberry Pi v2. It has been designed to work with various C- and CS-mount lenses ....
Index: RPI-16332
Index: RPI-16332
Available, 24h shipping!
(Check quantity)
Regular price €64.88 Price €64.88

Camera ZeroCam OV5647 5MPx - wide-angled 120° for Raspberry Pi Zero

Module with the camera compatible with Raspberry Pi Zero v1.3. The device has a matrix OV5647 with a resolution of 5 Mpx 2592 x 1944 px, supports HD 1080p at 30 K/sec. The...
Index: ODS-12748
Index: ODS-12748
In stock, shipping 24 hours!
(Check quantity)
Regular price €14.63 Price €14.63

ArduCam OV5647 5Mpx camera with LS-2718 CS mount lens - for Raspberry Pi

Camera module with sensor OV5647 equipped with a lens LS-2718 CS mount with parameters: focal length 4.0 mm, the angle 93 ° , aperture 1.4, the format of 1/2.5". Plugged into a...
Index: ACM-06628
Index: ACM-06628
In stock, shipping 24 hours!
(Check quantity)
Regular price €36.51 Price €36.51