





Popular AVR microcontroller from ATmel in a case soldered on surface (SMD).
In our store you will also find quartz resonators and an AVR programmer.
1. Reset on microkcntroller AVR internally pulled up to VCC. The manufacturer in the technical note, however, it is recommended to attach an external resistor pull-up if the system is exposed to interference. We recommend you to add an external 10k Ohm resistor.
2. Converter analog-to-digital has a separate power pins. The manufacturer recommends a dedicated power line (via the oil seal around 10uH) and mass (weight analog and digital must be connected at one point of the PCB) to reduce interference. This will allow to obtain higher precision of the Converter. If the maximum resolution which offers Atmel (10bit), we do not need, it is not that we should lead the way. Pin AREF voltage reference for the sensor. Agrat give the opportunity of choosing the internal voltage reference. If we decide on such AREF should be connected via a 100nF capacitor to ground. The inductor and capacitors form a LC filter. Without applying these elements will also lose accuracy A/C. warning! even if the Converter is not used, connect the AVCC and AGND pins, because they are also food for PORTC.
5. The maximum clock frequency of this microcontroller is 16MHz. The values of the capacitors specified by the manufacturer in the documentation. In the example, for quartz 16MHz 22pF we.
4. Food. For each pair VCC-GND, the manufacturer recommends a 100nF capacitor. In addition, it is also desirable use of the throttle. However, from experience we know that Agrat are working fine without this element. Of course, it all depends on the environment in which they work. If there is space on the PCB is this the throttle to apply, for advice.
5. Connector ISP (In-System Programming) allows programming of the microcontroller, located on the target system. Use the SPI interface.
Posting the payment for the order on our account on a business day up to 10 AM means sending the goods on the same day!
The time of payment depends on the ELIXIR's hours session of the sender's bank and the recipient of the transfer. It may take up to 2-4 working days.
Only for prepaid orders shipped to Poland.
Austria, Belgium, Croatia, The Czech Republic, Denmark, Germany, Netherlands, Slovakia
Bulgaria, Estonia, France, Hungary, Italy, Latvia, Lithuania, Luxembourg, Portugal, Romania, Slovenia
Finland, Greece, Ireland, Sweden, Cyprus, Malta, Spain
No customer reviews for the moment.
Quartz resonator 12MHz - HC49 - low
The quartz resonator in the small through hole case.Temperature sensor DS18B20 - digital 1-wire THT
Digital temperature sensor DS18B20 with 1-wire interface. Works in range from -55 °C to 125 °C. It is supplied with the voltage from 3.0 V to 5.5 V.Quartz resonator 16MHz - HC49 - low
The quartz resonator in the small through hole case.LCD display 2x16 characters blue
Symbol: JHD162A B-W. Driver compatible with HD44780 . Blue negative. Backlight: white LEDs. Character color: white.Customers who bought this product also bought:
Ball Caster 3/8'' - plastic - Pololu 950
Lightweight plastic ball in the bowl with a diameter of 3/8 inches, it is used to support the front of the two-wheeled robot.Tamiya 70097 double gearbox - set
A set of two DC motors with Tamiya gears. The system is equipped with hexagon 3mm diameter shaft. The user can select the gears: 58:1, 203:1.CNY70 reflective optocoupler sensor
Reflective optocoupler used, for example, to distinguish the edges or for line detection. Case dimensions - 7 x 7 x 6 mm,through hole installation.AVR microcontroller - ATmega8A-AU SMD
Atmel microcontroller AVR with 32-led case soldered on surface - SMD. Voltage supply range from 2.7 V to 5.5 V, frequency up to 16 MHz, has 8 KB Flash, 1 KB RAM, 512 bytes of...AVR microcontroller - ATmega16A-PU - DIP
Popular microcontroller AVR from Atmel in a DIP case.Solarbotics RW2i Wheel - internal mount - Pololu 1127
A wheel with a tyre for high grip. Ideal for minisumo robots and linefollowers. Dimensions: 31.2 x 13.2 mmHeat shrink tube 1.6/0.8 red - 10pcs
The diameter before heat shrink: 1.6 mm diameter after heat shrink: 0.8 mm. Price for 10 x 1 meter.Heat shrink tube 1.6/0.8 black - 10pcs
Diameter before heat shrink: 1.6 mm, diameter after heat shrink: 0.8 mm. Price for 10 x 1 meter.Pololu MMA7361LC 3-axis analog accelerometer with reg.
3-axis acceleration sensor operating in the range of 1.5 G or 6G. It has a built in voltage regulator which provides power for: 2.2 V - 16 V. The system communicates via...Linear voltage regulator 5V L7805ABV - THT TO220
Stabilizer used to supply logic systems supplied with 5 V. The maximum output current is 1 A.Products from the same category
AVR microcontroller - ATmega644PA-AU - SMD
Microcontroller ATmega644PA-AU AVR from ATmel in a case soldered on surface (SMD). This version has support for touch-Atmel QTouch buttons.AVR microcontroller - ATtiny13A-MMU
Atmel microcontroller AVR in 10-pin QFN case. Voltage supply range from 1.8 V to 5.5 V, with a clock signal frequency to 20 MHz, 1 KB Flash, 64 B RAM, 64 B EEPROM.AVR microcontroller - ATmega128A-AU SMD
Popular microcontroller ATmega128a-AU from ATmel AVR family in a case soldered on surface (SMD).AVR microcontroller - ATmega32A-AU SMD
Popular microcontroller AVR from ATmel in a case soldered on surface (SMD).AVR microcontroller - ATmega88PA-AU SMD
Popular microcontroller AVR from ATmel in the case soldered on surface (SMD).AVR microcontroller - ATmega32U4-AU SMD
Microcontroller AVR from ATmel in a case soldered on surface (SMD). It has 32 KB Flash memory, 2.5 KB of SRAM and 1 KB EEPROM, 26 GPIO controller USB 2.0 Full Speed.AVR microcontroller - ATmega8A-AU SMD
Atmel microcontroller AVR with 32-led case soldered on surface - SMD. Voltage supply range from 2.7 V to 5.5 V, frequency up to 16 MHz, has 8 KB Flash, 1 KB RAM, 512 bytes of...AVR microcontroller - ATmega328P-AU SMD
Microcontroller AVR from Atmel in a case soldered on the surface (SMD was also used in the popular Arduino module).