MAX14870 - single-channel motor controller 36V/1.7A - Pololu 2961

Index: PLL-04200 EAN: 5904422367336

Single-channel DC motor controller. Continuous current per channel 1.7 A (momentary to 2.5 A). Supply voltage from 4.5 V to 36 V.

MAX14870 - single-channel motor controller 36V/1.7A - Pololu 2961
€11.00
€8.94 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Description: MAX14870 - single channel 36V/1.7A motor controller

The module based on the MAX14870 Instruments system allows to control one DC motor. The motor can be powered from 4.5 V to 36 V with a continuous current draw of up to 1.7 A, temporary (for a few seconds) to 2.5 A. Before use, we recommend to read thedocumentation ofthe MAX14870.

Polol MAX14870 motor controller specifications

  • Number of channels: 1
  • Supply voltage: 4.5 V to 36 V
  • Continuous current per channel: 1.7 A
  • Maximum instantaneous current per channel: 2,5 A
  • Maximum PWM signal frequency: 50 kHz
  • Reverse power supply protection
  • Dimensions: 15.5 x 13.0 mm
  • Weight: 5 g (without connectors)
  • Included module and goldpin connectors

Connecting the motor controller

Podłączenie jednokanałowego sterownika silników Pololu

In a typical application, it is enough to connect two control lines: DIR direction selection and PWM speed control. By default, the PWM signal on the board is pulled up to ground by a 100 kΩ resistor, so the controller is switched off. If there is no need to use speed control, a high state (logical one) must be specified on the PWM output.

The EN or ENABLE output disconnects the motor outputs. If the high state is given, the M1 and M2 outputs are in high impedance state. The EN is pulled to ground by a 100 kΩ resistor, which means that the circuit is switched on by default.

EN PWM DIR M1 M2 Mode of operation
1 X X

high

impedance

high

impedance

disconnected outputs

idle

0 1 0 GND VIN forward revolutions
0 1 1 VIN GND backwards
0 0 X GND GND

braking

outputs connected to the ground

1 - high state, 0 - low state, X - unconnected output

MAX14870 controller outputs

Opis wyprowadzeń sterownika silników Pololu

PIN Description
Vin Motor supply voltage from 4.5 V to 36 V.
GND The mass potential of the system.
M1 Outputs + to connect the motor outputs.
M2 Outputs - to connect the motor outputs.
DIR Logical input defining the direction of engine rotation.
PWM Logical input for speed setting. A PWM signal must be connected to this output. Default is low.
EN Logical input that switches the system to the sleep state when low state is given. Default is high state.
FAULT Logical output indicating error in low state. Not connected by default.

Current limitation

The system has the ability to limit the motor current. To do so, cut the path as shown in the drawing:

then solder the resistor in SMD 1206 housing. 100 mΩ resistor will limit current to 1 A, 200 mΩ to 0.5 A etc. See thedocumentationfor details.

Video

Film describing the operation of the H-bridge - direct current motor controller.

Voltage to 4.5 V
Voltage from 36 V
Current 1.7 A
Channels 1
Package width 7.7 cm
Package height 8.5 cm
Package depth 0.1 cm
Package weight 0.002 kg

Be the first to ask a question about this product!

Product reviews

MAX14870 - single-channel motor controller 36V/1.7A - Pololu 2961

5/5

Average grade

2

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Zdjęcia użytkowników

Customers who bought this product also bought:

Products from the same category: