- EOL
|
Attention! The product has been discontinued. Check other products in category. |
Product description: Khadas Edge-V Pro - Rockchip RK3399 Cortex A72/A53 + 4GB RAM
Khadas Edge-V Basic minicomputer with a powerful Rockchip RK3399 Dual-Core Cortex-A72 + Quad-Core Cortex-A53 processor. It has 4GB of DDR4 memory, 128GB of eMMC storage, built-in WiFi and Bluetooth 5, along with two USB Type-C connectors, one USB 3.0 connector, one USB 2.0 connector, 40 GPIOs, gesture sensor and IMU sensor, microSD card slots, as well as an M.2 drive, Ethernet port, HDMI, IR receiver, and three buttons.
Operating Systems for Khadas Edge-V
The Khadas Edge-V minicomputer runs Android, LibreELEC, Ubuntu, and Debian. The system can be uploaded to a microSD card, M.2 drive or directly to the minicomputer's internal memory.
|
Operating systems can be downloaded from the manufacturer's website. |
Khadas Edge-V Pro Minicomputer.
What is needed to run the Khadas minicomputer?
- AnAC adapter with a USB type C plug - from 5 V to 20 V (5 V recommended) with a current capacity of 2 A. The device has a USB C 3.0 connector with PD support.
- HDMI cable - to connect the device to a monitor.
- Mouse and keyboard - for control and data input to the device.
Communication in Khadas Edge-V
The minicomputer has basic communication interfaces found in PC class computers. The user has:
- two USB A + USB type Cconnectors, under which you can connect, for example, a mouse, keyboard or flash drive. If it turns out that there are not enough sockets, you can increase their number by using an external USB HUB.
- Ethernet Gigabit socket- the possibility of a direct connection to LAN.
- WiFi module - allows you to communicate with the wireless network 802.11b/g/n/ac.
- Bluetooth 5.0 module - enables data transmission via popular interface.
- GPIO x 40 pin - general purpose outputs/inputs that can be used to operate LEDs, buttons, motor controllers. Among them there are pins supporting interfaces: USB, I2C, SPI, I2S, SPDIF, ADC, STM8S MCU IOs.
- microSD slot - A slot for a microSD memory card that may be used to install an operating system.
- HDMI connector - transmits image to monitor.
- M.2 slot - allows to connect high-speed M.2 SSD drives.
- display and touch panel connector - allows you to connect the display with MIPI-DSI connector and touch panel with 10-pin FPC connector.
- Camera connector - the minicomputer has two MIPi-CSI connectors for connecting two 13 MPx cameras.
Description of the connectors in the Khadas Edge-V.
Ports in Khadas Edge-V.
Power supply in Khadas Edge-V
The chip uses a USB type C connector as its power source. The manufacturer recommends that the voltage given to the connector is 5.0 V, while the current capacity of the power supply used should be at least 2.0 A. We offer power supplies that meet these parameters, such as: Extreme 3.1 A power supply.
Khadas Edge-V Basic specification and comparison
| Basic information | ||
|---|---|---|
 |
 |
|
| Model | Raspberry Pi 4 model B | Khadas Edge-V Max |
| Release | 6 - 2019 r. | 2018 r. |
| Technical specifications | ||
| Core | Quad-Core ARM Cortex-A72 | Quad-Core ARM Cortex-A54 Dual-Core ARM Cortex-A72 |
| Operating Systems | Linux Raspbian Windows 10 loT |
Debian Ubuntu Android etc. |
| Clocking | 1.5 GHz | 1.5 GHz + 1.8 GHz |
| RAM | Three versions
|
4GB DDR4 |
| Memory | microSD card | microSD card 128GB eMMC memory M.2 solid state drive |
| GPIO socket | 40-pin (2x20 pin) connector 2.54 mm pitch |
Connector 40-pin (2x20 pin) 2.54 mm pitch |
| Power supply |
|
9 V to 20 V / 2 A - USB PD USB type C |
| Board dimensions | 85 x 56 x 17 mm | 82 x 58 x 13.5 mm |
| Interfaces | ||
| USB interface | 2x USB 2.0 - type A socket 2x USB 3.0 - type A socket |
1x USB 2.0 - type A socket 1x USB 3.0 - type A socket |
| Network interface | Ethernet port 100/1000 Mbps | 10/100/1000 Mbps Ethernet port RTL8211FD |
| WiFi Interface | Dual Band 2.4 GHz and 5 GHz 802.11 b/g/n/ac |
AP6398S 802.11a/b/g/n/ac 2X2 MIMO with RSDB |
| Bluetooth | Low Energy, BLE 5 | Bluetooth 5.0 |
| Camera | CSI slot | CSI slot |
| Touchscreen display | DSI socket | DSI socket |
| Video | 2 x microHDMI H.265 4K 60 fps H.264 1080p 30 fps OpenGLES 1.1, 2.0, 3.0 |
HDMI 4K |
| Communications | UART, SPI, I2C, GPIO | USB, I2C, SPI, I2S, SPDIF, ADC, STM8S MCU IOs |
| Additional | - | Gesture sensor: APDS-9960 IMU sensor: ICM-20602 |
