• EOL

E-paper E-Ink 5.83'' 648×480px SPI - display with HAT for Raspberry Pi - black and white - Waveshare 14597

Index: WSR-18898 EAN: 5904422371241
The e-paper display from Waveshare has a diagonal of 5,83'' and a resolution of 640 x 480 px. It uses E-Inktechnology, which makes our eyes do not get tired so much during prolonged use of the display. It works with voltage from 3.3 V to 4 V. It communicates via SPI interface and supports two colors: white and black. It is compatible with Raspberry Pi, Arduino, Jetson Nano and STM32.
E-paper E-Ink 5.83'' 648×480px SPI - display with HAT for Raspberry Pi - black and white -...
€56.50
€45.93 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Waveshare
Compatibility: Raspberry Pi

Attention!

The product has been discontinued. Check other products in category.

Product description: E-Ink 5.83'' 648 × 480 px SPI e-paper display with HAT overlay for Raspberry Pi - black and white - Waveshare 14597

Ane-paper (E-ink) displayfrom Waveshare with a diagonal of5.83'' and a resolution equal to640 × 480 px. It usesE-Inktechnology, which makes our eyes do not get tired so much during prolonged use of the display. It works with voltagefrom 3.3 V to 4 V. It communicates viaSPIinterface and supports two colors: white and black. It is compatible with Raspberry Pi,Arduino,Jetson NanoandSTM32.

Product compatible with Arduino and Raspberry

The manufacturer provides auser guidefor Arduino and Raspberry Pi.

Wyświetlacz o przekątnej 5,835.83" display from Waveshare.
Połączenie wyświetlacza z Raspberry Pi za pomocą nakładki HAT.Connect the display to the Raspberry Pi using the HAT overlay.

Special features

  • Displays last loaded page even after power off
  • Low power consumption, consumes power only at the time of refresh
  • Equipped with a 40 pin GPIO connector
  • Uses SPI communication interface to connect the display to Raspberry Pi / Jetson Nano / Arduino / STM32

Contents of the kit

  • 5,83'' display
  • E-Paper (E-ink) Driver HAT
  • Mounting kit for Raspberry Pi
  • Connection cable PH2.0 8-pin - 20 cm

Connectors

Pin Description
VCC Supply voltage 3.3 V.
GND Circuit ground.
DIN MOSI pin of SPI interface.
CLK SPI interface clock pin.
CS Chip select activated by a low state.
DC Data / command selection: high state - data; low state - commands
RST External reset activated by a low state.
BUSY Busy status output, activated by a low state.
Nakładka HAT posiada otwory montażowe o średnicy 3 mm.


The HAT overlay has mounting holes of 3 mm diameter.


Wyświetlacz wykorzystuje interfejs komunikacyjny SPI.The display uses SPI communication interface.

Technical specifications

  • Compatible with: Raspberry Pi / Arduino / Jetson Nano / STM32
  • Display type: E-paper (E-ink)
  • Diagonal size: 5,83''
  • Resolution: 648 × 480 px
  • Viewing angle: 170°
  • Displayed colors: black and white
  • Gray scale: 2
  • Supply voltage: 3.3 V / 5 V
  • Interface: SPI
  • External dimensions: 125.4 x 99.5 mm
  • Display dimensions: 119.23 x 88.32 mm
  • Pixel: 0.184 x 0.184 mm
  • Full refresh time: 5 s
Screen - type e-paper
Screen - diagonal 5.83''
Screen - interface SPI
Screen - interface GPIO

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: