Soldering station 2in1 Yihua 898BD hotair with fan - 700W

Index: DLT-10679 EAN: 5908272000238

Soldering iron grotowa (50 W) and hot air (hotair) in one. The total capacity of the station is 700 W. The device has an adjustable temperature and two LED displays. The venting is provided through a fan located in the flask.

Soldering station 2in1 Yihua 898BD hotair with fan - 700W
€67.90
€55.20 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: Yihua

Description

Station Yihua 898BD has two LED displays, which can read the temperature of hot air and flask soldering iron. Temperature adjustment is done using buttons, airflow with knob.

Stacja lutownicza 2w1 hotair i grotowa Yihua 898BD z wentylatorem w kolbie - 700W

The device has sensor in the mount that, when putting off flask, the station cooles the heating element.

 

Stable and effective airflow is provided through a fan located in the flask. The fan is driven by a brushless motor, which provides a much higher durability and reliability of the device.

 

Check out our offer of additional tips!

Specification
  • Supply voltage: 230 V / 50 Hz (network)
  • Power: 700 W
  • The control is performed using PID controller
  • Protection ESD Safe
  • Automatic cooling of the heating elements after station's shutdown
  • The station has an ergonomical body

 

Hotair Soldering Iron

  • Adjustable temperature of hot air from 100 °C to 480 °C
  • Temperature stability +/-1 °C
  • LED display
  • Temperature setting with buttons
  • Smoothly adjustable airflow via knob
  • Airflow up to 120 l/min
  • The venting is provided through a fan located in the knob

 
Grotto Soldering Iron 

  • The flask 907A
  • Regulation of the soldering tip temperature from 200 °C to 480 °C
  • Capacity: 50 W
  • Temperature stability: +/- 2 °C
  • The potential between tip and ground: up to 2 mV
  • The resistance between tip and ground: 2 Ohm

 

Includes:
  • Station Yihua 898BD
  • Stand for the flask hotair
  • Set of nozzles:
    • round with a diameter of 6 mm
    • round with a diameter of 9 mm
    • square 12x12 mm
  • Stand for the grotto flask along with a cleaning sponge
  • The grotto flask 907 A with a tip T-I
  • A gripper for lifting chips

 

First run

  • After delivery of equipment, it should not be immediately started.
  • Equipment must remain about 12 hours at room temperature before switching on.
  • All applications for damages caused by the premature commissioning of the equipment, will be denied.
  • You must completely remove the screw/screws from the bottom of the station if the source of an air supply is compressor. These screws are marked in red (1 or 3 screws depending on model).

 

Note

Heating elements (heaters) and the tips are not subject to warranty either expressed or implied, and replacing them is chargeable.

 

Our range of accessories for soldering:

 

Voltage to 220 V AC
Voltage from 240 V AC
Voltage nominal 230 V AC
Nominal power 700 W
Temperature 200 - 480 °C
Solder - Fan yes
Solder - real temperature reading yes
Solder - Hotair yes
Solder - Type A/C digital
Laboratory of the future Compatible
Package width 20 cm
Package height 17 cm
Package depth 28 cm
Package weight 2.382 kg

Be the first to ask a question about this product!

Product reviews

Soldering station 2in1 Yihua 898BD hotair with fan - 700W

4.7/5

Average grade

4

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Reviews:

Pavel 26.02.2024 Confirmed purchase Translated review
Not yet tested, it is a gift for my son.
Radomír 15.06.2023 Confirmed purchase Translated review
It met expectations. Satisfaction.
Norbert 22.12.2022 Confirmed purchase Translated review
Good quality,
Zbigniew Z. 21.05.2022 Confirmed purchase Translated review
I have no comments

Customers who bought this product also bought:

Products from the same category: