- EOL
|
Attention! The product has been discontinued. Check other products in category. |
Description
Minicomputer Odroid in version Xu4Q with a powerful processorSamsung Exynos5422 octa-core withCortex-A15 2.0 GHzquad-core + Cortex-A7 1.4 GHz quad-coreandpassive coolingin the form of radiator. Board has2 GB of RAM LPDDR3, built-in Ethernet Gigabit port, HDMI 2.0 port and three USB slots including 2x USB 3.0, 30 GPIO, connectors for memory card microSD, and the IR receiver. Works with Ubuntu 15.04 or Android 4.2.2.
The device has 3 USB slots, HDMI connector, an Ethernet port and many others.
This version has passive cooling in the form of radiators.
What it takes to run minicomputer Odroid?
- The microSD memory card or eMMC memory - carrier, on which installed is operating system
- AC adapter:
- 5 V / 4 Afor Odroid XU4 / XU4Q version
- Case - protects minicomputer from the influence of external conditions
- HDMI cable - to connect the device to the monitor
- Mouse and keyboard - to control and input data into the device
In our store arre also available optional accessories - in type of adapter wi-fi, touchscreen display or the module USB 3.0 - SATA
Operating system
Odroid XU4Qworks with Ubuntu 15.04 and Android 4.2.2 based on kernel 3.10 LTS. The drive of device, can be a microSD card or a memory Flash eMMC 5.0 HS400 module.
|
Systems Ubuntu and Android can be downloaded from the manufacturer's website. The installation is very simple - check out our manual! |
Mounted radiator with fan is included.
Communication
Odroid has the main communication interfaces, which can be found in office computers of PC class. In addition to the previously listed connectors for audio and video, the user has at his or her disposal:
- HDMI port - transfers the image on the monitor
- USB connectors, to which you can connect, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number using an external USB HUB. This version has 2 USB 3.0 and 1x USB 2.0
- GPIO x 30pin + 12pin 2mm raster - outputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers of motors. Among them are the pins, supportting interfaces: I2C, SPI and UART. You must purchase goldpin straps separately and solder them yourself.
- a slot for microSD - slot for memory cards microSD, on which can be installed the operating system.
Odroid has a microSD slot on the top side of tile. Card is not included and can be purchased separately.
|
Connectors GPIO Odroid XU4 Board have a non-standard I/O raster of 2 mm. |
Power
As a power source, the system uses the DC connector 5.5 x 2.1 mm. The manufacturer recommends that the voltage indicated on the connector had a value of 5.0 V and a minimum output current of the used power supply shall be not less than 4.0 A. You will find a special power supply in our assortment.
Specifications and comparison
| Basic information | ||||
 |
 |
 |
 |
|
| Model | Odroid C0 | Odroid C1+ | Odroid C2 | Odroid XU4Q |
| Specification |
||||
| Processor | Amlogic S805 | Amlogic S805 | Amlogic S905 | Samsung Exynos5422 |
| The core |
Quad-Core 32-bit ARM Cortex A5 |
Quad-Core 32-bit ARM Cortex A5 |
Quad-Core 64-bit ARM Cortex-A53 |
Octa-Core ARM Cortex-A15 ARM Cortex™-A7 |
| Graphics |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
3D Mali-T628 MP6 OpenGL ES 3.0/2.0/1.1 |
| Systems |
Ubuntu 14.04 Android 4.4 Kernel 3.10 LTS |
Ubuntu 14.04 Android 4.4 Kernel 3.10 LTS |
Ubuntu 16.04 Android 5.1 Kernel 3.14 LTS |
Ubuntu 15.04 Android 4.4.2 Kernel 3.10 LTS |
| Clock frequency | 1.5 GHz | 1.5 GHz | 1.5 GHz | 2 GHz / 1.4 GHz |
| Architecture | ARMv7 | ARMv7 | ARMv8 | ARMv7-A |
| RAM |
1 GB DDR3 SDRAM |
1 GB DDR3 SDRAM 792MHz |
2 GB DDR3 SDRAM 792Mhz |
2 GB LPDDR3 RAM 750Mhz |
| Memory |
microSD card UHS1 eMMC4.5 HS200 |
microSD card UHS1 up to 16GB eMMC4.5 |
microSD card UHS1 up to 128 GB eMMC5.0 |
microSD card UHS1 up to 64 GB eMMC5.0 |
| GPIO slot |
Connector 40-pin + 7-pin I2S (to solder) |
Connector 40-pin + 7-pin I2S |
Connector 40-pin + 7-pin I2S |
Connector 30-pin + 12 pin I2S pitch of 2mm |
| Power |
5 V / 2 A DC Jack |
5 V / 2 A DC Jack |
5 V / 2 A DC Jack |
5 V / 4 A DC 2,5x2,1mm |
| Board sizes | 58x56x11mm | 85x56x18mm | 85x56x18mm | 82x58x22mm |
| Interfaces | ||||
| USB-Host |
2 x USB 2.0 (option for soldering) |
4x USB 2.0 slot, type A |
4x USB 2.0 slot, type A |
2x USB 3.0 1x USB 2.0 slot, type A |
| USB OTG | - |
1x microUSB |
1x microUSB | - |
| Network interface | - |
Ethernet 10/100/1000 Mbit/s |
Ethernet 10/100/1000 Mbit/s |
Ethernet 10/100/1000 Mbit/s |
| The RTC system | Built-in | Built-in | - | - |
| Video | HDMI | HDMI | HDMI 2.0 4K/60 Hz | HDMI 1.4a |
| Audio |
HDMI / I2S |
HDMi |
HDMI / I2S |
HDMI |
| ADC converter |
2 channels 10-bit |
2 channels 10-bit |
2 channels 10-bit |
2 channels 10-bit |
| Communication |
UART, SPI, I2C, GPIO, ADC |
UART, SPI, I2C, GPIO, ADC |
UART, SPI, I2C, GPIO, ADC |
UART, SPI, I2C, GPIO, ADC |
Video
The introduction of the Odroid XU4 minicomputer
