Even after just having started an adventure of learning about robotics and electronics, you can already pay attention to some basic aspects of designing. One of them is that when you start to build a project of a system that includes a motor or servo, you need a control element to organize the device’s work. For this purpose, our Botland store has prepared a category where you can find Engine Control Elements (ECUs) for both motors and servo. In our offer you can find an extremely wide range of ECUs, which, depending on the model, give you the ability to control different robots. We made sure that the products are of the highest quality and come from trusted manufacturers. If you are looking for a ECU for yourself, you can be sure to find one that suits your needs. Each product comes with a description and specification that can help you make the right choice. If you have any questions, do not hesitate to contact our technical department, which will be more than happy to help you.
Motor drivers and servos
L293D - two-channel 36V / 0,6A motor driver - 5pcs
Two-channel motor controller. Supply voltage up to 36 V. Average current per channel 600 mA (momentary up to 1.2 A). Housing: DIP 16 (through-hole). Set contains 5 pcs of chips.A4988 - stepper motor driver RepRap 35V/2A - Pololu 1182
Stepper motor driver based on the A4988 system. Voltage supply in the range of 8 to 35 V with maximum current consumption of 2 A per coil. Maximum resolution: 1/16 of a step....TB6612FNG - two-channel motor controller 13.5V / 1A - Pololu 713
Pololu module with dual channel DC motor driver. It is powered from 4.5 V to 13.5 V. The continuous current per channel is 1 A, when both channels are connected the value...Stepper motor 28BYJ-48 5V / 0.1A / 0.03Nm with ULN2003 controller
Five wire stepper motor with driver on Darlington chip. It has an integrated 64:1 gear ratio, is powered by 5 V, and draws 100 mA current per coil. The holding torque...DRV8801 - single-channel motor controller 36V / 1A - Pololu 2136
Single-channel DC motor controller. Continuous current per channel 1 A (momentary to 2.8 A). Supply voltage from 8 V to 36 V.DRV8835 - two-channel motor controller 11V / 1,2A - Pololu 2135
Two-channel driver for DC motors. Continuous current per channel 1.2 A (temporary up to 1.5 A). Power supply from 2.0 to 11 V.MAX14870 - single-channel motor controller 36V/1.7A - Pololu 2961
Single-channel DC motor controller. Continuous current per channel 1.7 A (momentary to 2.5 A). Supply voltage from 4.5 V to 36 V.Stepper motor driver L9110 12V/0,8A
The driver module uses L9110 chips to control one stepper motor or two DC motors. Supply voltage is from 3 V to 12 V. Continuous current up to 800 mA.DRV8834 stepper motor driver Low-Voltage 10,8V 2A - Pololu 2134
Stepper motor controller based on the DRV8834 system allows you to control a motor with a current consumption of up to 1.5 A (momentary up to 2 A) per coil, with voltage from...DRV8838 - single-channel motor controller 11V/1,7A - Pololu 2990
Single-channel DC motor controller. Continuous current per channel 1.7 A (momentary to 1.8 A). Supply voltage up to 11 V.- Reduced price
- Promotion
TB6612FNG - two-channel driver for 15V/1.2A motors with connectors - SparkFun ROB-14450
SparkFun module with two channel DC motor driver. It is powered from 2.7 V to 15 V . Continuous current per channel is 1.2 A. It has soldered goldpin connectors.Cytron MDD3A - dual-channel 16V / 3A motor controller
The Cytron MDD3A motor controller has the ability to control 2 DC motors or 1 stepper motor. Continuous current per channel is 3 A (momentary 5 A). Supply voltage is from 4 V...Cytron MDD10A - dual-channel 30V / 10A motor controller
Two-channel DC motor controller. Continuous current per channel is 10 A (momentary 30 A) . Supply voltage is 5 V to 30 V . The controller works with logical voltage 3.3 V...DRV8833 - two-channel motor controller 10,8V/1,2A - Pololu 2130
Two-channel driver for DC motors. Continuous current per channel 1.2 A (temporary up to 2 A). Power supply from 2.7 to 10.8 V.- Reduced price
- Promotion
DRV8825 - stepper motor driver 45V / 2,2A - Pololu 2133
Stepper motor's driver based on the system DRV8825, allows you to control the motor with a current consumption of up to 1.5 A (with cooling up to 2.2 A) per coil, when...Qwiic Haptic Driver - DA7280 - SparkFun ROB-17590
A haptic/tactile controller manufactured by Sparkfun . The module features a small Linear Resonant Actuator (LRA) vibration motor and Dialog Semiconductor's DA7280 motor...MP6500 - stepper motor driver 35V / 2.5A - with analog current control - Pololu 2966
Stepper motor driver based on MP6500 chip . Powered by a voltage range of 4.5 - 35 V, with a maximum current consumption of 2.5 A per coil. Maximum resolution: 1/8 step. The...DFRobot - motor driver 5,5V/1,5A for BBC micro:bit
An overlay for micro:bit to control four DC motors , two stepper motors and eight servos (5.5V/1.5A). Additionally the module has 9 I/O pins Micro:bit.36v4 - High - Power Stepper Motor Driver 50V/6A - Pololu 3730
The DRV8711 stepper motor controller allows you to control one bipolar stepper motor. Powered from 8 V to 50 V, with a maximum current draw of 6 A per coil. Maximum...TB67H420FTG Dual/Single Motor Driver Carrier- Pololu 2999
Dual channel DC motor controller . Continuous current per channel 1,7 A (momentary up to 4,5 A). Supply voltage from 10 V to 47 V .TB67S249FTG Stepper Motor Driver Carrier 47V/4,5A - Pololu 2973
Stepper motor driver based on TB67S249FTG chip. Powered by a voltage range of 10 - 47 V , with a maximum current consumption of 4.5 A per coil. Maximum resolution: 1 / 32...DRV8835 - two-channel 11V / 1,2A engine controller - overlay for Raspberry Pi - Pololu 2753
Module with two-channel circuit DRV8835 operating with voltages from 2 V to 11 V and current up to 1.2 A per channel (max. 1.5 A). It can be connected directly to the GPIO...- Reduced price
- Promotion
Motor regulator DC 12-40V/10A/400W - with a speed control knob
A simple controller with an integrated rotary potentiometer to control the speed of a DC motor up to 400 W. Powered from 12 V to 40 V.MP6500 Stepper Motor Driver Carrier, Digital Current Control (Header Pins Soldered) - Pololu 2967
Stepper motor controller based on MP6500 system. Powered from 4.5 V to 35 V, with a maximum current consumption of 2.5 A per coil. Maximum resolution: 1/8th step. The module...Zobacz również
- Computer accessories
- Automobile accessories
- Cooling
- Diodes
- Sound and acoustics
- Mounting components
- Passive elements
- Wearables (e-textiles, smart clothes)
- Cameras and recorders
- Memory cards & disks
- Communication
- Converters
- Electronics courses
- Microcontrollers
- Animal repellers
- LED lighting
- Programmers
- Relays
- Voltage regulators
- Artificial intelligence
- Integrated circuits
- Displays and screens
- Tablets and smartphones
- Smartwatches
- Consoles
Base which is essential to progress further
Beginners may not know this, but the more advanced the user becomes in robotics and electronics, the better he or she knows how important a controller is for both the engine and servo. Therefore, we encourage you to see the offer of the Botland store. We put a great emphasis on the fact that you have to choose the best ECUs that have already gained the trust of customers. It is worth to choose the highest quality products to significantly reduce the time spent on developing the drive. This allows you to gain more space where you can focus on other aspects important to your project, and therefore advance it further. Bear in mind that we make every effort to make our list include manufacturers whose products have gained worldwide recognition. By choosing products from our Botland store you can be sure that you get the satisfaction with your purchase and your project can gain and develop further.
Variety of models for every purpose, for every project
We realize that different projects require different ECUs. Therefore, we make every effort to ensure that our offer includes a variety of ECUs, among which each user can be able to find a product for himself. This applies to both learners and more advanced users who know what they are looking for. In our offer we have prepared controllers for DC motors, i.e. machines that are radio-controlled. Moreover, you can find stepper controllers, which you can apply to all machines with rotating motors. Linear controllers can be ideal for machines operating with progressive motion. Brushless controllers are used in devices such as optical disks, hard disks and even electric scooters. The variety of our products is vast, and each of them is provided with the appropriate specification and short description. They all come from proven manufacturers and their quality has won the trust of customers all over the world. Check our offer and find out that we have what you need.
Drivers are the heart, engines are the muscles.
Motors and servo need ECUs to manage their work, just as muscles need a heart pumping blood to them. An ECU is literally an engine control unit, and so as the name suggests, its main function is to manage the entire machine. So you could say in a way that the ECU is the heart of the machine, thanks to which the engines receive commands to move. One example of this can be the combustion engine with fuel injection. It is worth noting that such a solution is more economical than a carburetor, and also more safe. Everything happens thanks to the controller, which determines the limit of high revolutions, and when this value is exceeded, it cuts off the fuel injection. The ECU can also determine the appropriate dose of fuel to ensure that there is no need to use suction. In conclusion, without the ECU, the machine cannot function properly. So check our offer now and choose the perfect components for your project.