- New
- Reduced price
- Sale
- Reduced price
- Sale
- Reduced price
- Sale
Motor drivers and servos - Strona 3
Loading...
M1U550 - single motor controller 22V/1,8A - UART interface - Pololu 5077
A controller from Pololu based on the M1U550 system enabling operation of a DC motor . It uses the UART TTL interface for communication. Works with engines powered by...
Index: PLL-23644
Index: PLL-23644
M3S550 - triple motor controller DC 22V/1,7A - for Arduino - soldered - Pololu 5068
Shield designed to work with Arduino, enabling control of three DC motors . It uses the I2C interface for communication. The controller supports motors powered with voltage...
Index: PLL-23649
Index: PLL-23649
DRV8434 stepper motor driver 48V/2A - with pin connectors - Pololu 3763
Stepper motor driver module with the DRV8434 chip from Texas Instruments, equipped with male pins for connection to a 16-pin socket or breadboard without the need for...
Index: PLL-24068
Index: PLL-24068
The 4EncoderMotor V1.1 module is a 4-channel motor driver with encoders , based on STM32 and BL5617 . It supports I2C communication and enables precise motor control,...
Index: MSS-25343
Index: MSS-25343
H2 High-Power 36v11 CS - single channel 60V/11A DC motor controller - Pololu 2993
High-current H-bridge DC motor driver with MOSFET transistors. Supports voltages from 5V to 60V and provides up to 11A continuous current without the need for a radiator....
Index: PLL-25651
Index: PLL-25651
TB6552FNG - two-channel motor controller
Two-channel bridge H. Continuous current per channel 0.8 A, temporary to 1 A. Maximum supply voltage 15 V. SSOP-16 (SMD) housing.
Index: UCC-00777
Index: UCC-00777
Stepper motor driver L9110 12V/0,8A
The driver module uses L9110 chips to control one stepper motor or two DC motors. Supply voltage is from 3 V to 12 V. Continuous current up to 800 mA.
Index: MOD-09820
Index: MOD-09820
Cytron MD30C - single-channel 30V / 30A motor controller
Single channel DC motor controller. Continuous current per channel 30 A (momentary 80 A). Supply voltage from 5 V to 30 V.
Index: CTN-12402
Index: CTN-12402
Servo Driver - 16 servos for BBC Micro: Bit - Waveshare 15072
Expansion board for module Micro:bit. It allows you to control 16 servos through the I2C interface with 12-bit resolution for each channel.
Index: WSR-13308
Index: WSR-13308
24V/10A PWM/USB motor controller - DFRobot DRI0050
DC motor or LED strip driver, controlled via PWM interface. The driver allows you to adjust the speed of the motor or the brightness of the LED strip through the...
Index: DFR-20683
Index: DFR-20683
Motor Driver Carrier Board - 2x3A DC motor driver - carrier board for UNIHIKER - DFRobot DFR1136
A carrier board that allows you to control two DC motors with a maximum current of 3 A each, designed for the UNIHAKER minicomputer. It uses a connector with an inclined...
Index: DFR-25397
Index: DFR-25397
Haptic Motor Driver - DRV2605L - SparkFun ROB-14538
SparkFun module with DRV2605L haptic motor controller. It can handle ERM and LRA motors. Operates from 2 V to 5.2 V. Communicates over I2C bus.
Index: SPF-08219
Index: SPF-08219
Grove - PCA9685 - 16-channel server driver, 12-bit PWM I2C
A 16-channel PWM generator useful when there is no microcontroller output. It allows, among others: controlling servomechanisms, adjusting motor speed or changing LED...
Index: SEE-13511
Index: SEE-13511
DC Motor Driver HAT V1.0 - 2-channels motor driver 12V/1,2A - HAT for Raspberry Pi - DFRobot DFR0592
Two-channel DC motor controller TB6612FNG operating with voltage from 7 V to 12 V and continuous current 1.2 A per channel and momentary 2 A. The module in the form of an...
Index: DFR-15298
Index: DFR-15298
Linear Actuator Driver FDI 24 V + remote
Versatile controller with the wired remote control, designed for the FDI actuators. It also allows you to control any actuator with a voltage of 24 V DC and a current not...
Index: MOD-06481
Index: MOD-06481
Driver for sliding gates KSE380/KSE180
Control unit for sliding gates KSE180 / KSE380 with a radio receiver with a frequency of 433.92 MHz.
Index: MOD-06508
Index: MOD-06508
- Reduced price
- SPECIAL OFFERS
DFRobot HR8833 - two-channel driver for DC 10V/1,5A motors
A miniature, two-channel DC motor controller. The device operates on the basis of PWM signal. The motor supply voltage is from 3.3 V to 10 V, maximum current is 1.5 A.
Index: DFR-06934
Index: DFR-06934
DFRobot - Dual channel DC motor driver - 27V/7A
A two-channel DC motor controller. The device operates on the basis of PWM signal. Supply voltage for motors ranges from 6.5 V to 27 V, the maximum current is 7 A.
Index: DFR-07421
Index: DFR-07421
TB6612FNG - two-channel driver for 15V/1.2A motors with connectors - SparkFun ROB-14450
SparkFun module with two channel DC motor driver. It is powered from 2.7 V to 15 V . Continuous current per channel is 1.2 A. It has soldered goldpin connectors.
Index: SPF-10666
Index: SPF-10666
TB67H420FTG Dual/Single Motor Driver Carrier - Pololu 2997
Single channel DC motor controller. Continuous current per channel 2.6 A (momentary up to 5 A). Supply voltage from 4.5 V to 28 V .
Index: PLL-12059
Index: PLL-12059
Grove - L298P - two-channel motor driver 12V/2A - Seeedstudio 105020093
A module with an L298P motor controller that supports two DC motors or one stepper motor. The voltage supported by the controller is between 6 V and 12 V and the continuous...
Index: SEE-16906
Index: SEE-16906
Servo driver 16-channel, 16-bit PWM do Raspberry Pi Pico - Waveshare 19767
Expansion module for Raspberry Pi Pico to control 16 servos with 16-bit resolution. It uses PWM interface for communication. The module is also equipped with an output...
Index: WSR-19721
Index: WSR-19721
HRB8825 2-channel stepper motor driver 28V/2,5A - HAT For Raspberry Pi - Waveshare 22311
Two-channel stepper motor driver from Waveshare, in the form of a HAT shield for the Raspberry Pi. The controller is based on two HR8825 systems, it works with a voltage from...
Index: WSR-21705
Index: WSR-21705
M1T550 - single motor controller 22V/1,8A - I2C interface - Pololu 5075
A controller from Pololu based on the M1T550 system enabling operation of a DC motor . It uses the I2C interface for communication. Works with engines powered by voltage...
Index: PLL-23645
Index: PLL-23645
See also
- Computer accessories
- Cooling
- Diodes
- Sound and acoustics
- Mounting components
- Passive elements
- Wearables (e-textiles, smart clothes)
- Cameras
- Memory cards & disks
- Communication
- Converters
- Electronics courses
- Microcontrollers
- Animal repellers
- LED lighting
- Programmers
- Relays
- Voltage regulators
- Artificial intelligence
- Integrated circuits
- Displays and screens
- Tablets and smartphones
- Consoles