- EOL
Attention! The product has been discontinued. Check other products incategory. |
Description: Odroid C1+ - Amlogic S805 Quad-Core 1.5GHz + 1GB RAM
Odroid minicomputer in C1+ version with Amlogicquad-core 32-bitARM-7Cortex-A5 1.5 GHzprocessor. The board has1 GB of DDR3 RAM memory, built-in Ethernet port, HDMI port and four USB ports, 40 GPIO, microSD card and IR receiver connectors. Works withUbuntu 14.04orAndroid 4.2systems.
The device has 4 USB ports, HDMI and Ethernet port and many others.
What do I need to run my Odroid minicomputer?
- MicroSD memory card or eMMC memory- the media on which the operating system will be installed.
- The power supply:
- Enclosure- protects the minicomputer from external conditions
- HDMI cable - toconnect the device to a monitor
- Mouse and keyboard- to control and enter data into the device
Additional accessoriesare also available in our shop-such asWiFicard,touch screen orUSB 3.0 - SATAmodule.
Operating system
Odroid C1+ works with Ubuntu 14.04 and Android 4.2 systems based on 3.10 LTS kernel. The drive can be a microSD card or eMMC 4.5 HS200 Flash memory module.
Ubuntu and Android systems can be downloaded fromthe manufacturer's website. Installation of the system is very easy -check our manual! |
The set includes a heatsink.
Communication Odroid C1+
Odroid has basic communication interfaces, which can be found in PC-class office computers. In addition to the previously mentioned audio and video interfaces, the user has at his disposal:
- four USB connectors,under which you can connect e.g. a mouse, a keyboard, a WiFi card or a flash drive. If it turns out that there are too few connections, you can increase their number usingan external USB HUB.
- Ethernet socket, i.e. the possibility of direct connection to the LAN.
- GPIO x 40 pin- general purpose outputs/inputs that can be used to operate LEDs, buttons, motor controllers. Among them there are pins supporting interfaces: I2C, SPI and UART.
- microSD slot- slot for a microSD memory card, on which the operating system can be installed.Odroid has a slot for amicroSD memory cardon the back of the board. The card is not included in the set and can be purchased separately.
Power supply
As a power source, the system uses a DC Jack connector. The manufacturer recommends that the voltage given on the connector should be 5.0 V, while the current capacity of the power supply used should be at least 2.0 A. In our offer you will finda dedicated power supply.
OdroidC1+ hasanHDMIport,Ethernetportand a40-pinGPIO connector.
Enclosures for Odroid C1+
In our offer you will finddedicated enclosuresthat protect your Odroid minicomputer against external conditions. Dedicatedpower suppliesare also available.
In the picture you can see Odroid minicomputer in a dedicatedcase.
Specification and comparison of Odroid C0, Odroid C1+, Odroid C2, Odroid XU4
Basic information | ||||
Model | Odroid C0 | Odroid C1+ | Odroid C2 | Odroid XU4 |
Specification |
||||
Processor | Amlogic S805 | Amlogic S805 | Amlogic S905 | Samsung Exynos5422 |
Core |
Quad-Core 32-bit ARM Cortex A5 |
Quad-Core 32-bit ARM Cortex A5 |
Quad-Core 64-bit ARM Cortex A53 |
Octa-Core ARM Cortex-A15 ARM Cortex™-A7 |
Graphics |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
ARM Mali 450MP OpenGL ES 2.0/1.1 |
3D Mali-T628 MP6 OpenGL ES 3.0/2.0/1.1 |
Systems |
Ubuntu 14.04 Android 4.4 Kernel 3.10 LTS |
Ubuntu 14.04 Android 4.4 Kernel 3.10 LTS |
Ubuntu 16.04 Android 5.1 Kernel 3.14 LTS |
Ubuntu 15.04 Android 4.4.2 Kernel LTS 3.10 |
Clocking | 1.5 GHz | 1.5 GHz | 1.5 GHz | 2 GHz / 1.4 GHz |
Architecture | ARMv7 | ARMv7 | ARMv8 | ARMv7 |
Memory RAM |
1 GB DDR3 SDRAM |
1 GB DDR3 SDRAM 792MHz |
2 GB DDR3 SDRAM 792Mhz |
2 GB LPDDR3 frame 750Mhz |
Memory |
microSD card UHS1 eMMC4.5 HS200 |
microSD card UHS1 to 16 GB eMMC4.5 |
microSD card UHS1 to 128 GB eMMC5.0 |
microSD card UHS1 to 64 GB eMMC5.0 |
GPIO socket |
40-pin connector + 7 pin I2S (to be soldered) |
40-pin connector + 7 pin I2S |
40-pin connector + 7 pin I2S |
30-pin connector + 12 pin I2S 2mm raster |
Power supply |
5 V / 2 A DC Jack |
5 V / 2 A DC Jack |
5 V / 2 A DC Jack |
5 V / 4 A DC 2.5x2.1mm |
Dimensions of the tiles | 58x56x11mm | 85x56x18mm | 85x56x18mm | 82x58x22mm |
Interfaces | ||||
USB Host |
2 x USB 2.0 (option to be soldered in) |
4x USB 2.0 socket type A |
4x USB 2.0 socket type A |
2x USB 3.0 1x USB 2.0 socket type A |
USB OTG | - |
1x microUSB |
1x microUSB | - |
Network interface | - |
Ethernet 10/100/1000 Mbit/s |
Ethernet 10/100/1000 Mbit/s |
Ethernet 10/100/1000 Mbit/s |
RTC system | Built-in | Built-in | - | - |
Video | HDMI | HDMI | HDMI 2.0 4K/60Hz | HDMI 1.4a |
Audio |
HDMI / I2S |
HDMi |
HDMI / I2S |
HDMI |
ADC transmitter |
2 channels 10-bit |
2 channels 10-bit |
2 channels 10-bit |
2 channels 10-bit |
Communication |
UART, SLEEPING, I2C, GPIO, ADC |
UART, SLEEPING, I2C, GPIO, ADC |
UART, SLEEPING, I2C, GPIO, ADC |
UART, SLEEPING, I2C, GPIO, ADC |
Video
Presentation of the Odroid C1+ minicomputer.
Useful links |