Laser engraving machine / plotter Neje 3 - N30610 2,5W - 170x170mm
Various types of devices that did not fit into any of the other converter subcategories. Most often these are integrated circuits or modules that are supposed to provide communication between two independent tools. Among others we have converters using such interfaces as I2C, SPI, HDMI, VGA, UART or USB adapters. In this category you will find over 50 useful converters that will come in handy for many projects - both electronic and robotic.
I2C converter for HD44780 LCD display
The I2C converter for the popular display with controller HD44780 for example, 2x16 characters. Thanks to this system, two data lines and supply 5 Volts and groundare enough...
USB adapter for female cables with USB-UART converter PL2303 - Waveshare 7965
The adapter allows you to connect a USB to many different modules, with built-in converter USB to UART PL2303. Completed with female wire connectors. The system is compatible...
MCP2221A - USB to GPIO ADC I2C - Stemma QT / Qwiic - Adafruit 4471
The module is based on the MCP2221A system, equipped with GPIO ports, ADC analog inputs and I2C interface, to which access is possible via the USB type C connector. On...
FT232H - USB converter for UART, SPI, I2C, GPIO - Adafruit 2264
Board allows you to communicate with the modules and sensors directly from the computer. It supports the most popular interfaces: UART, I2C, SPI, it also has some GPIO pins.
Module NE555 - regulated frequency generator
The module works as a timer, pulse generator or oscillator application. It can be used as a time delay. Works with voltages from 5 V to 12 V. Board size: 30 x 13 mm.
HX711 - amplifier for a strainer beam - SparkFun SEN-13879
Operational amplifier is designed to handle strain beams. The system is supplied with the voltage from 2.7 V to 5.0 V, communicates via a two-wire bus: the data line and a...
Voltage divider 5V/25V for Arduino
A voltage divider is used, when the measured voltage has a larger value than the A/D converter's range. The device works in the range from 0 V to 25 V. The output voltage has a...
Four-channel opto-isolator A87 TLP281
4-channel opto-isolator designed to connect digital systems such as microcontrollers 5 V for high voltage systems. Maximum input voltage is 24 V.
QwiicBus EndPoint - SparkFun COM-16988
QwiicBus system component, allowing to extend the range of the I2C communication bus. It uses NXP PCA9615 chip, which converts two default I2C signals (SDA data line and SCL...
AR1100 - controller for resistive touch screens - Adafruit 1580
The module allows you to use the touch screen as from a normal computer mouse on any operating system. Tested with Windows, MacOs and Raspbian (Raspberry Pi).
2-CH UART To Ethernet Converter, Serial Port Transparent Transmission Module
2-CH UART TO ETH is a module that allows communication between TTL UART and RJ45 Ethernet . It allows bidirectional, transparent data transmission. The module is equipped...
MAX98357A decoder stereo DAC I2S - SparkFun DEV-14809
The stereo decoder's module DAC to communicate through the I2S interface. Built-in class D amplifier can provide up to 3.2 W of power to the speakers or headphones with...
Converter HDMI to VGA HD31B + audio
Compact size high-resolution image converter from HDMI signal to VGA D-SUB. It converts audio output to analog audio jack output (jack-jack cable included in the kit).
ISO1540 - I2C bidirectional isolator - STEMMA AT / Qwiic - Adafruit 4903
Bidirectional I2C isolator manufactured by Adafruit. It is used in projects that require electrical separation of devices on the same bus. Equipped with ISO1540 chip,...
Ethernet 10/100 Mb/s - UART Converter for Raspberry Pi Pico - Waveshare 20410
Ethernet to UART converter for Raspberry Pi Pico, enabling network communication via UART. The device supports four operating modes : TCP Client, TCP Server, UDP Client, UDP...
Driver for SPI alphanumeric display - SparkFun COM-10103
Driver based on the A6282 system allows you to control the alphanumeric segmented display using the SPI bus.
Grove - ADC converter for HX711 load cell sensors - Seeedstudio 101020712
Arduino compatible 24-bit ADC converter module allows to read values from pressure sensors. It has built-in amplifier with optional 32 dB, 64 dB and 128 dB gain. On the board...
Clock Generator - signal generator - 8kHz-160MHz I2C - Si5351A - STEMMA QT / Qwiic - Adafruit 5640
Clock signal generator from Adafruit, which was based on the SI5351A chip. It has been equipped with a 25 MHz crystal oscillator and has an internal PLL loop, thanks to...
Two-channel optoisolator ILD213T - SparkFun BOB-09118
2-channel opto-isolator designed to control systems with voltages up to 70 V through the system of digital 3 - 5V, e.g., microcontrollers. The module protects the system of...
OpenScale - strain-gauge bridge ATmega328P - SparkFun SEN-13261
Module for measuring the weight and temperature. It is used to read data from the strain-gauge sensors. It allows for calibration, setting the sampling frequency and accuracy....
SenseCAP S2100 - data logger/DTU - LoRaWAN - Seeedstudio 114992872
SenseCAP S2100 is a LoRaWAN data logger that is used to wirelessly collect and transmit data from environmental sensors. It is resistant to difficult weather conditions and...
MB85RS64V - 64Kb / 8KB FRAM non-volatile SPI memory - Adafruit 1897
Module with non-volatile FRAM memory for data storage which is characterized by low power consumption and very high durability. The system capacity is 64 KB (8 KB), it...See also
Find all converters, which for various reasons could not be found in any other subcategory of this equipment. It is worth to browse through this offer as there are many devices that may turn out to be a perfect solution to your problems encountered when connecting independent elements. You'll find cable adapters that make it easier to access specific pins or simply set them in a different configuration to match a particular standard. We also offer accessories that work with small logic circuits to ensure that the signal received at the output is properly processed so that a second device can read it. Many products in the range are designed to work with tools popular among robotics and electronics engineers, such as Arduino, Raspberry Pi or popular displays.
In the "other converters" category we offer, among other things, electronic component test kits. These allow for testing PNP and NPN bipolar transistors, diodes (and many other tools), and also have PWM and rectangular signal generators or frequency meters. Such devices usually have a screen on which the quantities relevant to the component are displayed. Among the simpler tools we have many types of adapters from HDMI to VGA, converters that allow the conversion of analogue audio and video signals to digital (inputs: PAL, NTSC, 2 x RCA chinch and USB A output), devices that convert digital audio to analogue, splitters for I2C or adapter from USB to female wires. We also have converters for connecting digital systems (e.g. microcontrollers) to high voltage systems, frequency generators (e.g. sine or rectangular signal), tools allowing the computer to communicate directly with sensors (UART, SPI, I2C, GPIO) or modules for connecting microcontrollers to CAN bus. We also offer voltage dividers, various drivers, optoisolators, boards with operational amplifiers, hubs and bridges for strain gauge beams, as well as FRAM memory or analogue signal isolator.
