Module GSM GPRS dual SIM c-uGSM μ-v shield.1.13 - for Arduino and Raspberry Pi - SMA connector

Index: RPI-05135 EAN: 5904422363185

The module supports GSM and GPRS communication. It allows for voice calls, sending SMS messages. On the board are: two connectors for SIM card, powering module for battery LiPol, as well as POWER and RESET buttons. Version works with Arduino and Raspberry Pi, it has a connector for antenna SMA.

Module GSM GPRS dual SIM c-uGSM μ-v shield.1.13 - for Arduino and Raspberry Pi - SMA connector
€38.84
€31.58 tax excl.
Waiting time: 2-4 weeks
Temporarily unavailable
30-day returns
PayPal payment
Manufacturer: Itbrain Power
Compatibility: Arduino Raspberry Pi

Description

The module working withArduinoandRaspberry Pi (in version 3B, 2B, B+ and A+)that provides communication in GSM and GPRS. It allows for voice calls, sending SMS messages and transfering data. On the board are: 2 connectors for SIM-cards, powering module for battery LiPol and a slot u.FL to mountan external antenna.

 

The system works withArduinoandRaspberry Pi (in version 3B, 2B, B+ and A+), it has a connector u.FL to connectan external antenna. In our offer you will also findthe module with SMA connectorand specialvoltage converters.

 

Moduł GSM GPRS dual SIM - Arduino i Raspberry

The distribution of elements on the board c-uGSM μ-shield.

 

Specification

  • Driver: Quectel M95F
  • Supported standards: GSM / GPRS
  • Frequencies: 850 / 950 / 1800 / 1900 MHz
  • Support standard DTMF
  • Two connectors for SIM-cards (one connection is active at the moment)
  • Antenna connector SMA
  • Audio interface
    • Output: 700 mV RMS
    • Input: capacitor MIC
  • Built-in converter USB to UART (USB connector can be used to power the module)
  • Automatic selection of logic levels between 3 V to 5 V
  • Buttons of modem: Power and Reset
  • It works withArduinoandRaspberry Pi, along with sample codes from manufacturer
  • Two mounting holes with diameter of: 2.5 mm
  • Board sizes: 40 x 32 mm

 

Detailed module description can be found in the user guide in partfirstandsecondand onthe website of the manufacturer.

 

Pins

Moduł GSM GPRS dual SIM

 

Pin Description
CTS Input Clear to Send - details indocumentation.
RTS Output Ready to Send - details indocumentation.
STATUS The statuspin.
RI The output Ring Indicator - details indocumentation.
GROUND The groundof the system.
Vcc 4V IN/OUT Input/output 4 V. When using battery, you need to include a LED (e.g., 1N14148) between the positive pole of battery and BkBat+ on the board, the anode heading the battery.
Vin 5V LiPol IN Input 5 V to charge with a LiPol battery.
Vusb 5V OUT The output is 5 V.
ON/OFF The control of a supply voltage of the system GSM (On/Off).
RESET GSM system reset.
TX (RXD) Communication via the serial interface.
RX (TXD) Communication via the serial interface.
LiPol +/- Connecting the battery LiPol, respectively "+" and "-".
ANTENNA CONNECTOR UFL OR SMA Antenna connector, depending on version of the SMA or u.FL.
AGND Ground for analog audio ports.
SPK +/- Output to speakers, respectively "+" and "-".
MIC +/- Microphone's input, respectively " + " and "-".
Backup bat +/- Backup battery, respectively "+" and "-". When using the battery, you need to include a LED (e.g., 1N14148) between the positive pole of battery and BkBat+ on the boar, the anode heading the battery.

The connection to the Arduino

The system works with Arduino Uno using the following pins:

 

Pin Arduino Description
GSM RX D3 Communication via the serial interface.
GSM TX D2 Communication via the serial interface.
RESET D6 GSM system reset.
ON / OFF D7 The control of a supply voltage of the system GSM (On/Off).
VIN (5 V LiPol) 5 V

Power supply 5 V. Details of the connection in the battery LiPol case, are available inthe manufacturer's manual.

GND

GND The ground of the system.

STATUS

D5 The statuspin.

 

Check out the example of project for Arduino -home alarm system!

 

Connect to the Raspberry Pi

To launch the module with the Raspberry Pi, you must perform the following connections:

 

Pin RPi Description
GSM RX 10

Communication via the serial interface (don't work in the USB communication).

GSM TX 08

Communication via the serial interface (don't work in the USB communication).

RESET 18 GSM system reset.
ON / OFF 16 The control of a supply voltage of the system GSM (On/Off).
VIN (5 V LiPol) 02/04 The supply voltage of 5 V.

GND

04/14 The ground of the system.
STATUS 12 The statuspin.

 

Same-day shipping

  • Crediting the payment for the order on our account on a business day before 10:00 AM means sending the goods on the same day.
  • All packages are being delivered by GLS Group courier and covered with insurance up to 1200 EUR.
  • You will receive a link to track your package and monitor the progress of delivery as soon as it is shipped.

Terms of delivery 

GLS - zone 1

Austria, Belgium, Croatia, The Czech Republic, Denmark, Germany, Netherlands, Poland, Slovakia 

  • Delivery time: 2-4 days
  • Delivery cost: from 4.18 EUR
  • Insurance: 1200 EUR
GLS - zone 2

Bulgaria, Estonia, France, Hungary, Italy, Latvia, Lithuania, Luxembourg, Portugal, Romania, San Marino, Slovenia

  • Delivery time: 2-5 days
  • Delivery cost: from 5.35 EUR
  • Insurance: 1200 EUR
GLS - zone 3

Finland, Greece, Ireland, Spain, Sweden 

  • Delivery time: 2-7 days
  • Delivery cost: from 7.67 EUR
  • Insurance: 1200 EUR

Payment methods

Card image cap
PayPal
  • Botland is a PayPal verified seller. Protect your financial information with this fast, safe and secure online payment system.

Card image cap
PayU
  • Choose easy and quick PayU e-payment method. Your financial information will stay secure.

Customers who bought this product also bought:

Products from the same category: