Pololu G2 High-Power 24v21 - 40V/21A motor controller
Pololu G2 High-Power 24v21 - 40V/21A motor controller
Pololu G2 High-Power 24v21 - 40V/21A motor controller
Pololu G2 High-Power 24v21 - 40V/21A motor controller
Pololu G2 High-Power 24v21 - 40V/21A motor controller
Pololu G2 High-Power 24v21 - 40V/21A motor controller
Pololu G2 High-Power 24v21 - 40V/21A motor controller - zdjęcie 1
Pololu G2 High-Power 24v21 - 40V/21A motor controller - zdjęcie 2
Pololu G2 High-Power 24v21 - 40V/21A motor controller - zdjęcie 3
Pololu G2 High-Power 24v21 - 40V/21A motor controller - zdjęcie 4
Pololu G2 High-Power 24v21 - 40V/21A motor controller - zdjęcie 5
Pololu G2 High-Power 24v21 - 40V/21A motor controller - zdjęcie 6

G2 High-Power 24v21 - single-channel motor controller 40V / 21A - Pololu 2995

Index: PLL-05722

Single-channel high-performance DC motor controller. Continuous current per channel is 21 A (momentary up to 100 A), motor supply voltage from 6.5 V to 40 V, logical part voltage from 1.8 V to 5.5 V. The device also has a current flow sensor and the possibility to limit the motor current.

€34.86
€28.34 tax excl.

Available, 24h shipping!
(Check quantity)
Shipping in 24 hours
30-day returns
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Product description: G2 High-Power 24v21 - 40V/21A single channel motor controller - Polol 2995.

The module allows to control one DC motor. The motor can be supplied with voltages from 6.5 to 40 volts with a continuous current consumption of up to 21 A, temporary (for 10 ms) to 100 A. Speed can be controlled by PWM signal, direction by digital DIR output - giving low (logical 0) or high (logical 1) state. The device also has a current flow sensor and the possibility to limit the motor current.

Specification

  • Number of channels: 1
  • Motor supply voltage: 6.5 V to 40 V
  • Supply voltage of the logical part: 1.8 V to 5.5 V
  • The outputs operate at 5 V
  • Continuous current: up to 21 A
  • Temporary currents: up to 100 mA (for several ms)
  • PWM signal frequency: 100 kHz
  • Current sensor sensitivity: 0.02 V/A
  • Security:
    • against reverse connection of the supply voltage
    • against too low a supply voltage
    • before a short circuit
  • Dimensions: 33 x 20 mm
  • Weight: 5,0 g
  • Modules, goldpin and screw connections included

When using a fully charged battery, the real voltage can be significantly higher than the nominal voltage. Therefore, the manufacturer recommends the use of batteries with a nominal output voltage up to 28 V.

The set includes a controller and connectors for self-soldering.

Connection

For proper operation of the module, it is necessary to supply power to the motors between the VIN and GND pins and connect the outputs responsible for motor movement, which are described in the table below.

PINDescription
VIN Motor supply voltage from 6.5 V to 40 V
VM Power output after reverse connection protection.
+/- Soldering out to solder an additional capacitor on the motor supply lines.
3V3 (OUT) Output voltage from the regulator 3.3 V, with a current capacity of several mA. Can be used as a reference voltage for other systems. Special care must be taken not to short circuit the adjacent pins.
GND System weight

OUTA

OUTB

Outputs for DC motor connection.
PWM Speed control input for PWM signal connection. Default is in low state
DIR Digital input to control the direction of motor rotation. Low state by default.
SLP If a low state is given, the system is put into standby mode. By default, the output is in the high state - the system is armed.
FLT An open-drain output that indicates the occurrence of a fault. The appearance of a low state indicates a system fault.
CS 20 mV/A current sensor output with 50 mA offset.
VREF Reference voltage input. Connect the resistor to ground to limit the maximum output current. Without additional resistor the maximum value is 50 A.

Operating modes and current limitation

The table shows the dependencies of the outputs on the input signals:
H - high state

L - low state

X - no matter

PWM

DIR

OUTAOUTBEngine condition

%

H H L

The motor is clockwise at % PWM.

%

L L H

The motor turns counterclockwise at % PWM

L

X L L Braking.

The PWM signal frequency should be up to 100 kHz, typically 20 kHz is used. The speed is proportional to the filling of the PWM signal. Additionally, the system has a VREF pin to limit the flowing current. The default value is limited to 50 A, a resistor between VREF and ground should be connected in shifts. The resistance dependence is shown in the diagram.

Motor current depending on the resistance connected between the VREF pin and ground.

Error detection conditions

The controller can detect various errors signaled by setting the FLT pin to low. In order to use it, it must be connected to a high state (system logic voltage). Short circuit on the outputs, too low voltage and overheating can be detected. All errors disable the motor outputs but do not block them, this means that the controller will try to resume operation after the error has disappeared.

The controller can handle large current surges for a short time (100 A for several milliseconds). In continuous operation it can withstand 21 A, but this depends on external conditions such as ambient temperature and motor cooling. A heat sink can be added to the plate to improve performance.

The controller has no automatic shutdown in case of overheating. Care must be taken to avoid damaging the system.

Video

Film describing the operation of the H-bridge - direct current motor controller.

List of G2 High Power controllers

Name

Voltage

power supplies

The current

Continuous

G2 High-Power 18v25 30 V 25 A
G2 High-Power 18v17 30 V 17 A
G2 High-Power 24v21 40 V 21 A
G2 High-Power 24v13 40 V 13 A

Voltage to 6.5 V
Voltage from 40.0 V
Current 21.0 A
Channels 1

Same-day shipping

Posting the payment for the order on our account on a business day up to 10 AM means sending the goods on the same day! 

Terms of delivery 

GLS - zone 1

Austria, Belgium, Croatia, The Czech Republic, Denmark, Germany, Netherlands, Poland, Slovakia 

  • Delivery time: 2-4 days
  • Delivery cost: from 4.18 EUR
  • Insurance: 1200 EUR
GLS - zone 2

Bulgaria, Estonia, France, Hungary, Italy, Latvia, Lithuania, Luxembourg, Portugal, Romania, Slovenia, Spain, The United Kingdom

  • Delivery time: 2-5 days
  • Delivery cost: from 5.35 EUR
  • Insurance: 1200 EUR
GLS - zone 3

Cyprus, Finland, Greece, Ireland, Malta, Spain, Sweden 

  • Delivery time: 2-7 days
  • Delivery cost: from 7.67 EUR
  • Insurance: 1200 EUR


Be the first to ask a question about this product!

No customer reviews for the moment.

You might also like

Micro Gearmotor HP 30:1 1000RPM with Extended Motor Shaft - Pololu 2212

Polol's miniature 30:1 high power motor with a gearbox, 1000 rpm, 0.57 kg*cm (0.056 Nm) torque. It has an extended shaft for mounting speed sensors.
Index: PLL-00010
Index: PLL-00010
Available, 24h shipping!
(Check quantity)
Regular price €16.72 Price €16.72

Micro metal gearmotor HP 10:1 3000RPM - Pololu 999

Polol's miniature 10:1 high power motor with a gearbox, 3000 rpm, 0.22 kg*cm (0.021 Nm) torque.
Index: PLL-00015
Index: PLL-00015
Available, 24h shipping!
(Check quantity)
Regular price €14.86 Price €14.86

HP Motor with 50:1 Gear - doublesided shaft - Pololu 2213

Polol's miniature 50:1 high power motor with a 630 rpm gearbox, torque is 1.1 kg*cm (0.107 Nm). It has an extended shaft for mounting speed sensors.
Index: PLL-00037
Index: PLL-00037
Available, 24h shipping!
(Check quantity)
Regular price €16.16 Price €16.16

DC Motor 120:1 120RPM - angular - Pololu 1124

Small plastic motor with 120:1, 120 rpm, torque 1.4 kg*cm (0.137 Nm). The motor can be an alternative to Polol micro motors.
Index: PLL-00121
Index: PLL-00121
Available, 24h shipping!
(Check quantity)
Regular price €5.09 Price €5.09

Raspberry Pi Model B 512MB RAM

Raspberry Pi Model B (512MB RAM) is a miniature computer that can successfully replace a large office device. The module allows you to process video in high definition. Has:...
Index: RPI-00972
Index: RPI-00972

Arduino Uno Rev3 - module A000066

The original module from the Arduino Uno with the AVR microcontroller ATmega328 in an interchangeable housing. It has 32 KB Flash memory, 2 KB RAM, 14 digital I/o of which 6...
Index: ARD-01060
Index: ARD-01060
In stock, shipping 24 hours!
(Check quantity)
Regular price €21.40 Price €21.40

Customers who bought this product also bought:

Linear voltage regulator 5V L7805ABV - THT TO220

Stabilizer used to supply logic systems supplied with 5 V. The maximum output current is 1 A.
Index: UCC-00081
Index: UCC-00081
Available, 24h shipping!
(Check quantity)
Regular price €0.26 Price €0.26

Step-Down Voltage Regulator D24V3F5 - 5V 0,3A - Pololu 2098

Step-down converter with 5 V output voltage. Maximum current up to 300 mA. Supply voltage in the range of 6 V - 42 V.
Index: PLL-01331
Index: PLL-01331
Available, 24h shipping!
(Check quantity)
Regular price €3.93 Price €3.93

Bridge rectifier KBPC5010 - 1000V / 50A - with connectors

Bridge rectifier, maximum working voltage 1000 V, current up to 50 amps . It has outputs in the form of connectors.
Index: PAS-05224
Index: PAS-05224
In stock, shipping 24 hours!
(Check quantity)
Regular price €0.92 Price €0.92

Step-Down Voltage Converter D24V22F5 - 5V 2,5A - Pololu 2858

Converter, type step down, with an output voltage of 5 V. Maximum current is 2.5 A. The voltage is in the range of 5.3 V to 36 V. Module dimensions - 18 x 18 mm.
Index: PLL-04978
Index: PLL-04978
Czas oczekiwania ok. 10-21 dni
Regular price €8.35 Price €8.35

Programmer / debugger STM8 / STM32 compatible with ST-LINK / V2 mini - Waveshare 10053

The device is used as the programmer and debugger for STM8 and STM32 modules. It works with voltages 3.3 V and 5 V, selectable by jumper.
Index: WSR-04481
Index: WSR-04481
In stock, shipping 24 hours!
(Check quantity)
Regular price €6.26 Price €6.26

Radiator RAD18 18x11x5mm

Heat sink with the size of  18 x 11 x 5 mm.
Index: ETN-01502
Index: ETN-01502
Czas oczekiwania: ok. 10-30 dni
Regular price €0.21 Price €0.21

Converter A/C and C/A PCF8591P 8-bit DIP

8-bit analogue-to-digital and digital-to-digital-toanalogue converter chip in a scrolling housing The communication interface is the I2C bus.
Index: UCC-01561
Index: UCC-01561
Unavailable
Regular price €2.77 Price €2.77

Thermally conductive glue 10g

AG TermoGlue thermo-conductive adhesive. Package contains 10 g of adhesive.
Index: CHE-02003
Index: CHE-02003
Available, 24h shipping!
(Check quantity)
Regular price €1.63 Price €1.63

Set of connectors and sleeves - 150 pcs.

Set includes insulated male, female, ring, fork connectors, and links and bushings.
Index: KAB-03530
Index: KAB-03530
In stock, shipping 24 hours!
(Check quantity)
Regular price €9.28 Price €9.28

Thermo-conducting tape Thermopad 20x130x2mm - 2.4W / mK

The tape improves the flow of heat between electronic elements. It is used in places where it is not possible to use thermal-conductive paste. Tape is...
Index: CHE-05703
Index: CHE-05703
In stock, shipping 24 hours!
(Check quantity)
Regular price €2.95 Price €2.95

AS5040 Magnetic Encoder

AS5040 non-contact magnetic encoder in a small form factor with 3 different modes of operation.
Index: SES-00663
Index: SES-00663
Unavailable
Regular price €11.37 Price €11.37

DC plug 5.5x2.1mm with quick connection

DC φ5.5 x 2.1 mm plug with connector allowing you to mount the cable with a screwdriver.
Index: KAB-01590
Index: KAB-01590
In stock, shipping 24 hours!
(Check quantity)
Regular price €0.44 Price €0.44

Products from the same category

L293D - two-channel 36V / 0,6A motor driver - 5pcs

Two-channel motor controller. Supply voltage up to 36 V . Average current per channel 600 mA (momentary up to 1.2 A). Enclosure: DIP 16 (scrolling). Set contains 5 pieces of...
Index: UCC-00176
Index: UCC-00176
Available, 24h shipping!
(Check quantity)
Regular price €2.07 Price €2.07

TB6612FNG - two-channel motor controller 13.5V / 1A - Pololu 713

Polol module with a two-channel direct current motor controller. It is powered from 4.5 V to 13.5 V. Continuous current per channel is 1 A, with both channels connected the...
Index: PLL-00032
Index: PLL-00032
Available, 24h shipping!
(Check quantity)
Regular price €3.84 Price €3.84

TB6612FNG - two-channel motor controller

Two-channel bridge H. Continuous current per channel 1.2 A temporary to 3.2 A. Supply voltage up to 15 V. SSOP-24 (SMD) housing.
Index: UCC-00495
Index: UCC-00495
Available, 24h shipping!
(Check quantity)
Regular price €2.08 Price €2.08

L298N - two-channel motor controller - 12V/2A

Module with dual-channel driver for DC motors L298. It is supplied with the voltage up to 12 V. Maximum current per channel is 2 A. The system has embedded voltage regulator 5...
Index: MOD-03164
Index: MOD-03164
Czas oczekiwania ok. 10-30 dni
Regular price €3.23 Price €3.23

DRV8835 - two-channel motor controller 11V / 1,2A - Pololu 2135

Two-channel DC motor controller. Continuous current per channel 1.2 A (momentary to 1.5 A). Power supply from 2.0 to 11 V.
Index: PLL-00851
Index: PLL-00851
Available, 24h shipping!
(Check quantity)
Regular price €4.16 Price €4.16

L298N - two-channel motor driver

Two-channel bridge H. Supply voltage: max. 46 V. Maximum instantaneous current 2 A. Enclosure: Multiwatt15 (THT).
Index: UCC-00060
Index: UCC-00060
Available, 24h shipping!
(Check quantity)
Regular price €3.00 Price €3.00

DRV8838 - single-channel motor controller 11V/1,7A - Pololu 2990

Single-channel DC motor controller. Continuous current per channel 1.7 A (momentary to 1.8 A). Supply voltage up to 11 V.
Index: PLL-02695
Index: PLL-02695
Waiting time approx. 10-21 days
Regular price €3.12 Price €3.12

DRV8801 - single-channel motor controller 36V / 1A - Pololu 2136

Single-channel DC motor controller. Continuous current per channel 1 A (momentary to 2.8 A). Supply voltage from 8 V to 36 V.
Index: PLL-01256
Index: PLL-01256
Available, 24h shipping!
(Check quantity)
Regular price €4.42 Price €4.42

VNH5019 - single-channel 24V / 12A motor controller - Pololu - 1451

Module with ST VNH5019 system working with voltages from 5.5 V to 24 V. Maximum continuous output current is 12 A (momentary: 30 A).
Index: PLL-00456
Index: PLL-00456
Available, 24h shipping!
(Check quantity)
Regular price €22.33 Price €22.33

DRV8833 - two-channel motor controller 10,8V/1,2A - Pololu 2130

Two-channel DC motor controller. Continuous current per channel 1.2 A (momentary to 2 A). Power supply from 2.7 to 10.8 V.
Index: PLL-00546
Index: PLL-00546
Available, 24h shipping!
(Check quantity)
Regular price €4.64 Price €4.64

Motor regulator DC 12-40V / 10A / 400W - with a speed control knob

A simple controller with an integrated rotary potentiometer to control the speed of a DC motor up to 400 W. Powered from 12 V to 40 V.
Index: MOD-06666
Index: MOD-06666
Available, 24h shipping!
(Check quantity)
Regular price €5.79 Price €5.79

L298N Dual H Bridge DC StepperMotor Driver Board - Iduino ST1112

Module with a two-channel direct current motor controller L298N. It is powered from 5 V to 46 V. The maximum channel current is 2 A. The system has a built-in voltage regulator...
Index: MOD-08227
Index: MOD-08227
Available, 24h shipping!
(Check quantity)
Regular price €5.09 Price €5.09