- EOL
|
Attention! The product has been discontinued. Check other products in category. |
Product description of ArduCam OV5640D
Camera module with matrixOV5640Dwith a resolution of5 MPxand the size of1/4"with the output of format JPEG, RAW, RGB and YUV. The camera has Autofocus. Transfer rate with full resolution of 2592 x 1944 px,is15 fps. It is equipped with a lensof 1/4". The device operates with a voltage of 3.3 V, it communicates through a parallel interface.
|
The product is compatible with Arduino |
A block diagram of the camera ArduCam OV5640D
The device consists of a sensor and an electronic part with a data buffer and bus controller.
A block diagram of the camera module ArduCAM.
OV5640D 5mpx Autofocus module specification
- Supply voltage: 3.3 V
- Matrix OV5640D, 5 MPx, 1/4" (documentation)
- Resolution: max2592 px x 1944(5 MPx)
- Pixel size: 1.4 x 1.4 µm
- Range of view: 3673,6 x 2738,4 µm
- Clock input speed: from 6 to 27 MHz
- Angle of view: 24 °
- Speed (fps):
- QSXGA (2592 x 1944): 15 fps
- 1080p: 30 fps
- 1280x960: 45 fps
- 720p: 60 fps
- VGA (640 x 480): 90 fps
- QVGA (320 x 240): 120 fps
- Output formats:
- YUV(422/420) / YCbCr422,
- RGB565/555/444,
- CCIR656,
- compressed 8-bit data
- 8 / 10-bit RAW RGB Data
- Lens1/4"
Pins of camera OV5640D
The device has soldered 22 pin connector, pitch of 2.54 mm.
| Pin | Name | Description |
|---|---|---|
| 1 | VCC | Supply voltage is 3.3 V. |
| 2 | GND | The ground of the system. |
| 3 | SCL | Clock line of the interface Two-Wire. |
| 4 | SDATA | Data line of the interface Two-Wire. |
| 5 | VSYNC | Vertical synchronization. |
| 6 | HREF | Horizontal synchronization. |
| 7 | PCLK | The clock output of the matrix's sensor. |
| 8 | XCLK | The input of the system clock. |
| 9 | DOUT9 | The video data output - bit 9 (MSB). |
| 10 | DOUT8 | The video data output - bit 8. |
| 11 | DOUT7 | The video data output - bit 7. |
| 12 | DOUT6 | The video data output - bit 6. |
| 13 | DOUT5 | The video data output - bit 5. |
| 14 | DOUT4 | The video data output - bit 4. |
| 15 | DOUT3 | The video data output - bit 3. |
| 16 | DOUT2 | The video data output - bit 2 (LSB). |
| 17 | DOUT1 | The video data output - bit 1 (10-bit mode). |
| 18 | DOUT0 | The video data output - bit 0 (mode of10-bit). |
| 19 | RESET | The reset signal of sensor, activated with the low state. |
| 20 | PWDN | Disabling the system by activating the high state. |
| 21 | AFVDD | The power for the VCM from 2.8 V to 3.3 V. |
| 22 | STB | The stroboscopic output. |
Useful links |
