ArduCam-Mini OV2640 2MPx 1600x1200px 60fps SPI - camera module for Arduino

Index: ACM-06556 EAN: 5904422358242

Camera module for Arduino 2 MPx with a resolution of 1600 px x 1200 and speeds up to 60 frames per second. It extends the capabilities of the microcontroller with the ability to shoot photos and record videos. The device operates with a voltage of 3.3 V and 5 V, it communicates via SPI, it has a sensitivity of 0.6 V/(lux*sec), the angle of view of 25°, the lens is 1/4".

ArduCam-Mini OV2640 2MPx 1600x1200px 60fps SPI - camera module for Arduino
€35.50
€28.86 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: ArduCam
Compatibility: Arduino

ArduCam-Mini OV2640 Description

Camera moduleforArduino2 MPx with a resolution of 1600 px x 1200 and speeds up to 60 frames per second. It extends the capabilities of the system, for example, microcontrollers Arduino,STM32andminicomputers Raspberry Pi, with the possibility of taking photos and recording video clips.Arducam mini OV2640operates with a voltage of 3.3 V and 5 V, it communicates viaSPI, it has a sensitivity of 0.6 V/(lux*sec), the angle of view of 25°, the lens is 1/4".

Kamera ArduCam 2MPx do Arduino

Modes of operation

  • Single Capture Mode- the default mode of the device after the indicating the command via SPI, the camera captures a frame and adds it to the buffer, while setting a flag in the registry. By checking the state of the flag, the user knows that the read has been completed.
  • Multiple Capture Mode- an advanced mode where the user specifies the number of frames to be captured. Please note that the number of frames cannot exceed the capacity of the buffer.
  • JPEG Compression- in this mode, the output are compressed data in the JPG format with higher resolution, than RGB.
  • Normal Read and Burst Read Operation- in this mode, it is sufficient to send a read command for receiving the continuous transmission of frames via an SPI interface.
  • Rewind the Read Operation- it allows to read, several times, the same data contained in the buffer.
  • Low Power Mode- disables the sensor and transducer in order to save energy.
  • Image Sensor Control- mode change parameters of the camera sensor, i.a. balance, brightness, contrast and saturation.

The product is compatible with Arduino

Auser manualandlibrary for Arduino are available in GitHub.

Block diagram

The device consists of a lens, sensor and electronic components with the data buffer and the controller of theSPIbus. The user has also access directly to the sensor via the I2C bus.

ArduCam-Mini OV2640

A block diagram of the camera module ArduCAM-Mini.

OV2640 SPI Specification

  • Working voltage: 3.3 V / 5 V
  • Resolution:1600 x 1200 Pixels(2 Megapixels)
  • The number of frames per second:
    • up to 60 FRAMES per second for CIF format
    • up to 30 FRAMES per second for SVGA format
    • up to 15 FRAMES per second for the format SXGA / UXGA
  • Lens size: 1/4 "
  • Lens mounting: CS-mount / M12
  • Sensitivity: 0,6 V/(lux*sec)
  • Angle of view: 25 °
  • Output formats:
    • 422/420 YUV / YCbCr 422
    • RGB565/555
    • Compressed 8-bit data
    • 8 / 10-bit RAW RGB Data
  • Configuration of sensor through I2C bus
  • Module dimensions: 35 × 25 mm

Pins 

The device has soldered the 8 pin connector, pitch of 2.54 mm.

ArduCam-Mini  - podłączenie

Pin Name Description
1 CS Chip Select - selects a device on the SPI bus, activated by low state.
2 MOSI Data output line of SPI bus.
3 MISO Data output line of SPI bus.
4 SCLK Clock line of the SPI bus.
5 GND The ground of the system.
6 5V Supply voltage from 3.3 V to 5 V
7 SDA Data output line of I2C bus.
8 SCL Clock line of the I2C bus.

 

Interface SPI / I2C
Resolution 1600x1200px
Camera - matrix OV2640
Camera - lens CS-mount / M12
Camera - format 1/4 ''
Camera - type module
Package width 4 cm
Package height 4 cm
Package depth 4 cm
Package weight 0.018 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: