- EOL
|
Attention! The sale of the product has been completed. Check otherdevices in this category. |
Description
The board contains an ATSAMD21G18 microcontroller with a 32-bit ARM Cortex M0 core. The module is equipped with 20 digital inputs/outputs of which 18 can be used as PWM outputs (e.g. for motor control) and 6 analog inputs with higher than previously 12-bit resolution. Another distinguishing feature of this model is the presence of a 10-bit analogue DAC output. The circuit is clocked with a 48 MHz clock signal. The outputs work with a voltage of 3.3 V.
The subject of sale is the original Genuino product from the distributionwww.arduino.cc.
|
Unlike ArduinoM0, GenuinoZero and ArduinoM0 Proversionsandhave an integrated debugger (EDBG - Atmel Embedded Debugger), which allows you to preview the program during execution. To support this function you need dedicated Atmel environment. In our offer there isArduino M0board available - without integrated debugger. Apart from Arduino M0 debugger you can program using environment, which is available at:www.arduino.cc. |
The connector layout is compatible with Arduino Uno, it means that the Shields will be compatible provided they work with 3.3V. M0 Pro has two microUSB sockets:
- Programming - socket dedicated to upload software via Arduino IDE environment or debugging via EDBG,
- Native - allows you to connect USB devices, also allows programming and connection to a serial monitor.
Main features
Below are some features that distinguish the modules from other programmable tiles.
| The name | Description |
|---|---|
|
Installed bootloader |
Thanks to the installed bootloader, the appropriatemicroUSB cable andsoftware from the manufactureris sufficient to program the device. |
|
ARM Cortex M0 32-bit |
The board contains an ATSAMD21G18 microcontroller with a powerful 32-bit ARM Cortex M0 core. |
|
Debugger EDBG |
Genuino Zeroo has an integrated debugger - Atmel Embedded Debugger, which allows you to preview during program execution. Atmel's dedicated environment is required to support this feature. |
|
Arduino Shield |
The layout of the connectors enables installation of dedicatedArduino Shieldcovers, provided that they operate at 3.3V. |
|
Extracts digital |
14 digital inputs/outputs enable, among other things, to control LEDs, relays and read button statuses. |
|
Performance Current |
The maximum current capacity of a single output is 7 mA. |
|
Outputs PWM |
The 18 PWM outputs allow e.g. for motor control and LED brightness adjustment. |
|
Inputs analogue |
6 inputs of the built-in 12-bit analogue-to-digital converter support, among others, sensors with analogue output. |
|
Communication serial |
The device supports popular communication interfaces, among others: UART, I2C and SPI. |
|
Memory Embedded |
ATSAMD21G18 chip is clocked with 48 MHz signal, has 256 kB program memory and 32 kB SRAM. |
|
Power supply DC connector |
Any power supplyfrom 6V to 15V with a 5.5 x 2.1mm DC connector can be used to power Genuino. |
|
Power supply USB port |
You can power the board from your computer viathe microUSB cable,whilekeeping in mindthat the maximum current capacity of the USB port is 500 mA. Genuino has a system that protects the socket against short circuits and excessive current flow. |
|
The connector is . ICSP |
The module has ICSP outputs, on which the SPI interface has been output. |
|
Pin IOREF |
The IOREF pin allows for direct access to the voltage with which the I/O outputs work. |
|
Built-in LED |
The connected LED on pin 13 allows debugging of simple programs. |
The layout of the components on the Genuino Zero board.
Specification .
- Power supply voltage: 5 V
- The voltage of the leads: 3,3 V
- Maximum current from one output: 7 mA
- Microcontroller: ATSAMD21G18
- The core: ARM Cortex-M0 32-bit
- Maximum clock frequency: 48 MHz
- SRAM: 32 kB
- Flash memory: 256 kB
- EEPROM memory: none
- Ports I/O: 20
- PWM outputs: 18
- Number of analog inputs: 6 (12-bit A/C converter channels)
- Number of analog outputs: 1 (10-bit DAC converter channel)
- Serial interfaces: UART, SPI, I2C
- Connected LED
|
Due to the conflict within the Arduino team, two versions of the environment were available to download from: Genuino tiles come from the distribution ofArduino.cc.When installing software downloaded from a source other than those described on the back of the module, you will receive a message about an unauthorized tile supplier. You can cancel it with one click and the environment will work properly. |
Useful links |
