• EOL

Feather M0 wi-fi 32-bit + connector.Fl - Arduino-compatible - Adafruit 3061

Index: ADA-05969 EAN: 5904422354374

A small module with a 32-bit microcontroller ARM Cortex M0 ATSAMD21G18 known from Arduino Zero and with wi-fi ATWINC1500 module. Feather is designed for portable projects. On board is a microUSB connector, through which the system can be programmed via the Arduino IDE. On the board is a connector u.FL for attaching the external antenna wi-fi.

Feather M0 wi-fi 32-bit + connector.Fl - Arduino-compatible - Adafruit 3061
€46.50
€37.80 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Adafruit

Attention!

The product has been discontinued. Check other products in category.

Description

A small module with a 32-bit microcontroller ARM Cortex M0 ATSAMD21G18 and wi-fi module ATWINC1500. Feather is designed for portable projects. Thanks to the microUSB connector and uploaded bootloader, module can be programmed from the Arduino IDE. Board has a small size, can be supplied voltage from USB port or rechargeable battery 3,7 V LiPol. On the board is a connector u.FL for attaching the external antenna wi-fi.

Key features

  • Built-in microcontroller with Cortex M0+, it has a 12-bit ADC transducer, 10-bit DAC, supports UART, SPI, I2C and PWM, DMA, native USB
  • The device has built-in wi-fi ATWINC1500 module that works in 802.11 b/g/n standard. It supports Soft AP and SSL mode, and WEP, WPA and WPA2.

  • On the board is a connector u.FL to connectan external wi-fi antenna - in our offer there are also SMA - u.FL adapters.
  • System features the compact dimensions, the board has only: 54 x 23 x 8 mm, its weight is approx. 6 g.
  • On board is a built-in charging system Li-Pol cells with current delivery up to 200 mA.
  • 20 pins of GPIO allows you to connect any devices, to pin 13, as in the Arduino, connected was the LED

 

 

Check out how to start playing with the Adafruit Feather!

 

Mobile projects

Controller Feather is designed for mobile projects. Thanks to the integrated connector, it is possible to power it from the rechargeable LiPol battery 3.7 V. The battery voltage was led through an analog pin, so you can constantly monitor the state of charge of the lipol. Also available is powering from the microUSB port.

 Adafruit Feather M0 WiFi 32-bit, arduino, moduł,kontroler,

 

On the board there is a connector u.FL to connectan external wi-fi antenna- in our offer, there are also SMA - u.FLadapters.

 

Programming (Arduino IDE)

The module can be programmed using the Arduino IDE. For this, you will need to configure the software in a way provided by the manufacturer and connect the board using the microUSB cable. The settings of the Arduino IDE are available on the website of the manufacturer.

 

Specification

  • Supply voltage: lipol 3.7 V or USB 5 V slot
  • ATSAMD21G18 ARM Cortex M0 3.3 V microcontroller:
    • Flash memory: 256 KB
    • SRAM: 32 KB
    • Clock frequency: internal oscillator 48 MHz
  • Built-in wi-fi module ATWINC1500:
    • Support for Soft AP and SSL
    • Protections: WEP, WPA, WPA2
  • Installed Arduino bootloader
  • Works with a modified version of the Arduino IDE
  • MicroUSB connector for programming, in our offer, you will find the appropriate wire
  • Installed voltage regulator AP2112K-3.3 3.3 V with current delivery up to 300 mA
  • Power supply from USB port or with a lipol battery 3.7 V
  • 20 GPIO pins
  • 8 PWM outputs
  • 10 analog inputs (one for the battery voltage measurement)
  • 1 x analog output
  • Built-in lipol charging module 200 mA with LED which informs about the status
  • LED for pin 13
  • The reset button
  • This kit includes the goldpin connectors for self-soldering.
  • Dimensions: 54 x 23 x 8 mm
  • Weight: approx. 6 g

 

Voltage to 5.0 V
Voltage from 5.0 V
Voltage output from 3.3 V
Output voltage to 3.3 V
Nominal output voltage 3.3 V
UC - Microcontroller ATSAMD21G18
UC - Core 32-bit ARM Cortex M0
UC - Flash 256 kB
UC - RAM 32 kB
UC - core 1. Single Core
UC - Digital pins 20
UC - analog in 10
UC - freq 48 MHz
UC - C/A 1
UC - PWM 8
UC - WiFi yes
UC - USB microUSB
UC - I2C yes
UC - UART yes
UC - SPI interface yes
Package width 10 cm
Package height 14 cm
Package depth 0.4 cm
Package weight 0.009 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: