• EOL

Camera ArduCam OV2640 2MPx + WiFi ESP8266 module

Index: ACM-07066

Module with OV2640 2 MPx camera with a resolution of up to 1600 x 1200 px, and wi-fi ESP8266 chip. The device allows, for example, for transmission of video over HTTP or websocket protocol. The module is equipped with a charging system and can be powered by battery.

Camera ArduCam OV2640 2MPx + WiFi ESP8266 module
€39.90
€32.44 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: ArduCam

Attention!

The product has been discontinued. Check others products incategory.

Description

Module with 2 Mpx camera and wi-fi ESP8266 system - Arduino-compatible. The device allows, for example, for transmission of video over HTTP or websocket protocol. The module is equipped with a power system and may be powered using rechargeable battery.

Kamera ArduCam 2MPx do Arduino

 

The device consists of two modules:

  • ArduCAM-Mini-2MP-V2
  • ArduCAM-ESP8266-Nano

They can be used both separately and together

First run

  1. Download and install the Arduino IDE version 1.6.8 from:www.arduino.cc

  2. Start the Arduino IDE, select"File" - > "Settings"

  3. In place Additional URLS for the Manager of a board, specify:
    hhttp://www.arducam.com/downloads/ESP8266_UNO/package_ArduCAM_index.json
  4. SelectTools -> Board -> Manager of boards
  5. Install the module ArduCam_ESP8266_Uno (probably at the bottom of the list)

 

 

Description of programming of the board using theArduino IDEcan be found inthe user guide. Examples of programs are available after you install the libraries directly from the Arduino IDE.

 

Sample programs

  • ArduCAM_Mini_OV2640_Capture (or ArduCAM_Mini_OV5642_Capture)- allows you to create a site using the HTTP Protocol, which displays the image from ArduCam (camera ArduCam can be purchased separately).

  • ArduCAM_Mini_OV2640_Capture2SD (or ArduCAM_Mini_ OV5642_Capture2SD)- allows you to save pictures taken with the camera on the microSD memory card (the camera ArduCamoraz and the memory card can be purchased separately).

  • ArduCAM_Mini_OV2640_Video2SD (or ArduCAM_Mini_OV5642_Video2SD)- allows to record the video basing on the format JPEG-n on the microSD card in AVI format (the camera ArduCamoraz and the memory card can be purchased separately).

The set includes the camera ArduCAM-Mini-2-V2 and the communication module ArduCAM-ESP8266-Nano.

The module consists of a lens, sensor and electronic component with the data buffer and the controller of the SPI bus. The user has access directly to the sensor via the I2C bus.

ArduCam-Mini OV2640

A block diagram of the camera module ArduCAM-Mini.

Specification

  • Working voltage: 3.3 V / 5 V
  • Resolution: 1600 x 1200 Pixels (2 Mpx)
  • The number of frames per second:
    • up to 60 FRAMES per second for CIF format
    • up to 30 FRAMES per second for SVGA format
    • up to 15 FRAMES per second for the format SXGA / UXGA
  • Lens size: 1/4 "
  • Lens mounting: CS-mount / M12
  • Sensitivity: 0,6 V/(lux*sec)
  • Angle of view: 25 °
  • Output formats:
    • 422/420 YUV / YCbCr 422
    • RGB565/555
    • compressed 8-bit data
    • 8 / 10-bit RAW RGB Data
  • Configuration of sensor through I2C bus
  • Module dimensions: 35 × 25 mm

Pins ArduCAM-Mini-2MP-V2

The module has soldered the 8-pin connector, pitch of 2.54 mm.

ArduCam-Mini  - podłączenie

PinNameDescription
1 CS Chip Select - selects a device on the SPI bus, activated by low state.
2 MOSI Output data line of SPI bus.
3 MISO Output data line of SPI bus.
4 SCLK Clock line of the SPI bus.
5 GND The ground of the system.
6 5V Supply voltage from 3.3 V to 5 V
7 SDA Output data line of I2C bus.
8 SCL Clock line of the I2C bus.

The pins of the module wi-fi ArduCAM-ESP8266-Nano

ESP8266 Arducam

PinArduinoESP8266Description
1 RST RST Reset of the module.
2 A0 A0 The analog input, the maximum voltage of 3.3 V.
3 GND GND Ground.
4 D0 GPIO16 I/O digital line.
5 D5 SCK

I/O digital line.

Clock line of bus SPI - SCK.
6 D6 MISO

I/O digital line.

Data line of SPI - MISO bus.
7 D7 MOSI

I/O digital line.

Data line of SPI - MOSI bus.
8 3V3 3.3 V The output voltage from the regulator of 3.3 V.
9 GND GND Ground
10 D8 GPIO15

I/O digital line with resistor pulling-up to10 kΩGND.

SPI - SS bus line.
11 D4 GPIO2

I/O digital line with resistor pulling-up to VCC 10 kΩ.

Pin-CS for reader ofmicroSD cards.

12 D3 GPIO0 I/O digital line with resistor pulling-up to VCC 10 kΩ.
13 Traffic GPIO4

I/O digital line.

Data line of I2C bus - SDA.
14 SCL GPIO5

I/O digital line.

The clock line of I2C - SCL bus.

15 RX GPIO3 Data line of interface UART - receiver.
16 TX GPIO1 Data line of interface UART - transmitter.

Specification

  • Working voltage of pins: 3.3 V
  • ControllerESP8266 ESP-12F
    • Flash memory: 4 MB
    • I/O Ports: 11
    • PWM outputs: 10
    • Number of analog inputs: 1 (channel of A/C converter)
    • Serial interfaces: UART, SPI, I2C, 1-Wire
    • External interrupts
    • The controller of a wi-fi network
  • Built-in microSD card reader (memory card can be purchased separately)
  • Built-in battery charger of a LiPol recchargeable battery 3.7 V / 500mA
  • Controller USB - UART: CH340
  • Compatible withthe Arduino IDE
  • MicroUSB socket (microUSB cable sold seperately)
  • Slot for battery LiPol (compatible cable included in the package)
  • Power connector: DC 5.5 x 2.1 mm
  • Board sizes: 69 x 54 x 15 mm

The contents of the set

  • Module ArduCAM-Mini-2MP-V2
  • The module ArduCAM-ESP8266-Nano
  • The power cable for the battery

Interface SPI / I2C
Resolution 1600x1200px
UC - Microcontroller ESP-8266
Camera - matrix OV2640
Camera - lens CS-mount / M12
Camera - format 1/4 ''
Camera - type module
Package width 0.001 cm
Package height 0.001 cm
Package depth 0.001 cm
Package weight 0.001 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: