|
Attention, the sale of the product is complete! Orange Pi minicomputers have been withdrawn from sale due to the manufacturer's failure to provide appropriate certification. We encourage you to familiarize yourself withother devices available in our offer. |
Description
Orange Pi Zero Plus2minicomputer with powerfulH5 quad-core ARM Cortex-A53processor. The board has512 MB DDR3 RAM,8 GB eMMC Flash,WiFi, Bluetooth, HDMI port, 1xmicroUSB OTG,26 GPIO,microSDcard slot andCSI cameraconnector. Works withAndroid, Lubuntu, Debian, Raspbian.
The device has 1 microUSB slot and HDMI port and many others.
What do I need to run an Orange Pi minicomputer?
- MicroSD memory card- the media on which the operating system will be installed.
- Power supply unitwith microUSB plug - with 5 V output voltage
Operating system
Orange Pi works with Ubuntu and Android systems and systems known from Raspberry Pi. The drive can be a microSD card with a capacity of up to 64 GB or built-in eMMC memory.
|
Ubuntu and Android systems can be downloaded fromthe manufacturer's website. Installation of the system is very easy -check our manual! |
Orange Pi Zero Plus2 - top view
Communication
Orange Pi has basic communication interfaces, which can be found in PC-class office computers. In addition to the previously mentioned audio and video interfaces, the user has at his disposal:
- one microUSB OTG socket,where you can connect e.g. a mouse, a keyboard, a WiFi card or a flash drive. If it turns out that there are too few sockets, you can increase their number usingan external USB HUB.
- WiFiand Bluetoothmodule- AP6212, for wireless communication in IEEE 802.11 b/g/n and BT 4.2 standards.
- GPIO x 26 pin + 13 pin connector- general purpose outputs/inputs that can be used for LEDs, buttons, motor controllers. Among them there are pins supporting I2C, SPI and UART interfaces.
- microSD slot- a slot for a microSD memory card, on which the operating system can be installed.
- CSI slot - after connecting the camera.
Power supply .
The system uses a microUSB socket connector as its power source. The manufacturer recommends that the voltage given on the connector should be 5.0 V, while the current capacity of the power supply used should be at least 2.0 A. In our offer you will findappropriate power supplies.
Specification
| Basic information | ||
 |
 |
|
| Model | ||
| Specification |
||
| Processor | H5 | H2 |
| Core |
Quad-Core ARM Cortex A53 |
Quad-Core ARM Cortex A7 |
| Graphics |
Mali450 GPU GPU @600MHz OpenGL ES 2.0 |
Mali400MP2 GPU @600MHz OpenGL ES 2.0 |
| Systems |
Ubuntu, Debian Android, Raspbian |
Ubuntu Android |
|
Memory RAM |
512 MB DDR3 |
512 MB DDR3 |
| Memory |
microSD card up to 32 GB eMMC 8 GB |
microSD card up to 64 GB |
|
Node GPIO |
26-pin connector + 13 pin |
26-pin connector + 13 pin |
| Power supply |
5 V / 2 A microUSB |
5 V / 2 A microUSB |
| Buttons | - | Power |
|
Dimensions
|
48x46mm | 48x46mm |
| Interfaces | ||
| USB Host | - |
1 x USB 2.0 socket type A |
| USB OTG | 1x microUSB | 1x microUSB |
|
Interface network |
0 |
10/100 Mbit/s |
|
Module WiFi |
Embedded AP6212 aerial and Bluetooth |
Embedded XR819 aerial |
| Video |
HDMI CSI - connector Cameras |
- |
| Audio | HDMI |
microphone |
| Interfaces |
UART, GPIO |
UART, GPIO |
Useful links |
