Step-Up Voltage Regulator U3V40F7 - 7,5V 4A - Pololu 4014

Index: PLL-20744 EAN: 5904422382407
Pololu brand step-up converter. The output voltage of the converter is 7.5 V and its current capacity is 4 A. The input voltage should be between 1.3 V and 7.5 V (the starting voltage is 2.7 V). Typical inverter efficiency is between 90% and 95%, depending on input voltage and load. The module has temperature protection, when the temperature threshold is exceeded, it will shut down.
Step-Up Voltage Regulator U3V40F7 - 7,5V 4A - Pololu 4014
€8.90
€7.24 tax excl.
Waiting time: 4-6 weeks
Only on request
PayPal payment
Step-up inverter - 4A - Pololu:
Manufacturer: Pololu

Product description: U3V40F7 - 7,5V 4A step-up converter - Pololu 4014

Pololu brand step-upconverter. The output voltage of the converter is 7.5 V and its current capacity is 4 A. The input voltage should be in the range from 1.3 V to 7.5 V (the starting voltage is 2.7 V). Typical inverter efficiency is between 90% and 95%, depending on input voltage and load. The module has temperature protection; it will shut down when the temperature threshold is exceeded.

Wyprowadzenia modułu przetwornicy7.5 V / 4 A step-up converter pinouts.

Leads of the step-up converter module

The module has four leads in the form of six holes for soldering connectors with a 2.54 mm pitch.

  • EN - pin to disable the system when the voltage is below 0.4 V, system on by default: 30 kΩ resistor pulled up from EN to VIN.
  • VIN - input voltage from 2.7 V to 7.5 V (after starting up the chip, the input voltage may be at least 1.3 V).
  • GND - system ground (common for VIN and VOUT).
  • VOUT - output voltage of 7.5 V.

Hazardous voltage pulses

When connecting the power supply to the module, dangerous, short eclectic impulses with high amplitude (peaks) may appear, which can permanently damage the system. Pololu company has performed tests which show that for input voltage above 11 V the peaks can have amplitude large enough to damage the module. In order to protect against this undesirable phenomenon it is recommended to solder a capacitor of at least 33 uF as close to the converter supply pins as possible.

System efficiency

Efficiency is defined as the ratio of output power to input power (power out)/(power in). It is a very important parameter when working with portable sources of energy (batteries and rechargeable batteries), where the time of work on one charging cycle counts. The efficiency of this circuit is from 90% to 95%. The output current depends on the input voltage and the system load.

Sprawność układuPerformance of the U3V40F7 step-up converter.
Zawartość zestawu
U3V40F7 7.5 V / 4 A step-up converter. Goldpin connectors included.

U3V40F7 step-up inverter specifications

  • Input voltage: from 1.3 V to 7.5 V (minimum voltage to start the circuit is 2.7 V)
  • Output voltage: 7.5 V (with 4% accuracy)
  • Typical efficiency: 90% to 95%, depending on input voltage and load
  • Switching frequency: ~600 Hz at high load
  • Energy-saving mode
  • Typical no-load idle current less than 2 mA
  • The 9.5 A switch allows for:
    • Instantaneous input current up to 9.5 A
    • Up to 4.5 A input current for a few seconds
    • up to 4 A input current for a longer time
  • Integrated protection:
    • shutdown due to over temperature
    • soft-start function limits the inrush current and gradually increases the output voltage
    • Output overvoltage protection (typically 16.5V)
    • input current limitation cycle by cycle up to 9.5 A
  • Dimensions: 15.2 x 15.2 x 5.6 mm
  • Weight: 1.5 g

Voltage to 1.3 V
Voltage from 7.5 V
Voltage output from 7.5 V
Output voltage to 7.5 V
Nominal output voltage 7.5 V
Current 4.0 A
Stabilizer - Type step-up
Package width 8.2 cm
Package height 9.5 cm
Package depth 0.5 cm
Package weight 0.003 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: