• EOL

Arduino Nano 33 BLE Sense with headers - module ABX00035

Index: ARD-14761 EAN: 7630049201576

Arduino® Nano 33 BLE Sense with connectors is a version of Nano 33 BLE equipped with a number of sensors. It is characterized by higher performance with lower power consumption thanks to the nRF52480 microcontroller. The small board is equipped with an accelerometer, thermometer, gyroscope, light intensity sensor, gestures and a digital microphone. It supports Bluetooth Low Energy.

Arduino Nano 33 BLE Sense with headers - module ABX00035
€64.90
€52.76 tax excl.
Product was replaced by other
Manufacturer: Arduino

Attention!

The product has been discontinued. Check other products in category.

Description: Arduino Nano 33 BLE Sense with connectors

The Arduino models in the Nano series are designed to extend the capabilities of small tiles to make their use possible in any project. Arduino Nano 33 BLE Sense is equipped with an energy-saving and efficientnRF52480 microcontrollercapable of operating at64 MHz. There is space for 1 MB of flash memory and 256 kB of RAM on board. Additionally, the small board was equipped with a number of sensors, which gives a lot of possibilities. Thanks to this unit, the Nano 33 BLE Sense board isthe most energy-efficientrepresentative of the Nano family, despite its dimensions. The board supportsBluetooth 5.0 Low Energystandard.

The board has soldered in leads. In our offer we also have a version without connectors.

Arduino Nano 33 BLE Sense

Arduino Nano 33 BLE Sense.

Possibilities of Arduino Nano 33 BLE Sense

Arduino Nano 33 BLE Sense is equipped with aU-block NINA B306module, managingBluetoothcommunicationin 5.0 LE standard.On board the Nano there is a 9-axis Inertial Measurement Unit (IMU)LSM9DS1communicating via I2C bus, which consists of a 3-axis gyroscope, accelerometer and magnetometer. Additionally, the small board is equippedwith LPS22HB temperature and pressure sensor,HTS221 humiditysensor,lightintensity, color and gesturesensorADPS-9960. There isalsospace for the MP34DT05 digital microphone. Additionally on board there was also cryptographic system ATECC608A.

Attention!

Arduino Nano 33 BLE Sense can work ONLY with 3.3V by default. Do not supply it directly with 5 V.

Arduino Nano 33 BLE Sensesupports only 3.3 Vby default. There is a jumper in place of 5V pin in standard Nano board (between RST and A7 pins) which can be shorted to USB power supply.To supply 5V power to the devices, solder the jumper and power Nano via USB. If the jumper is soldered and no voltage is obtained from the V in pin. This is a protection to protect the Arduino Nano 33 BLE Sense. The board allows debugging programs, which is done with 6 pads on the bottom of the board underneath the communication system.

Wyprowadzenia Arduino Nano 33 BLE Sense

The Arduino Nano 33 BLE Sense. Visible jumper for 5V power supply via USB.

Pin Designation Type Description
1 D13 Digital GPIO
2 + 3V3 Power output Power supply for external devices
3 AREF Analogue Reference pin, can be used as GPIO
4 A0 / DAC0 Analogue ADC input / DAC output, canbe used as GPIO
5

A1

Analogue ADC input,canbe used as GPIO
6 A2 Analogue ADC input,canbe used as GPIO
7 A3 Analogue ADC input,canbe used as GPIO
8 A4 / SDA Analogue ADC input, I2C SDA,can beused as GPIO*
9 A5 / SCL Analogue The ADC, I2C SCLinput can beused as GPIO*.
10 A6 Analogue ADC input,canbe used as GPIO
11 A7 Analogue ADC input,canbe used as GPIO
12 V USB I / Wy power supply Normally not connected. Can be shorted to USB power
13 RST Digital input Active reset
14 GND Power supply Mass
15 VIN Power supply Power supply
16 TX Digital USART TX,canbe used like GPIO
17 RX Digital USART RX,canbe used like GPIO
18 RST Digital Active reset
19 GND Power supply Mass
20 D2 Digital GPIO
21 D3 / PWM Digital GPIO,canbe used like GPIO
22 D4 Digital GPIO
23 D5 / PWM Digital GPIO,canbe used like GPIO
24 D6 / PWM Digital GPIO,canbe used like GPIO
25 D7 Digital GPIO
26 D8 Digital GPIO
27 D9 / PWM Digital GPIO,canbe used like GPIO
28 D10 / PWM Digital GPIO,canbe used like GPIO
29 D11 MOSI Digital SPI MOSI,canbe used like GPIO
30 D12 / MISO Digital SPI MISO,canbe used like GPIO

(*) Unlike the standard Arduino Nano, the A4 and A5 pins have a default pull-up, the so-called pull-up and are used as I2C bus, so it is not recommended to use them as analogue inputs.

Arduino Nano 33 BLE Sense PCB specification

  • Supply voltage: 3.3 V
  • Microcontroller:nRF 52840
    • Clock: 64 MHz
    • Flash memory: 1 MB
    • RAM 256 kB
  • Digital pins: 14
  • PWM pins: 6
  • Analogue pins: 8
  • MicroUSB socket
  • Interfaces: GPIO, SPI, I2C, USART, PWM
  • Transducers: ADC, DAC
  • Dimensions: 45 x 18 mm

Voltage from 3.3 V
Voltage nominal 3.3 V
Output voltage to 3.3 V
UC - Microcontroller nRF52840
UC - Core Cortex M4
UC - Flash 1 MB
UC - RAM 256 kB
UC - core 1. Single Core
UC - Digital pins 14
UC - analog in 8
UC - freq 64 MHz
UC - USB microUSB
UC - I2C yes
UC - UART yes
UC - Connector 5V microUSB
UC - SPI interface yes
Package width 6 cm
Package height 8.2 cm
Package depth 2.6 cm
Package weight 0.016 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: