- EOL
|
Attention! The sale of the product has been completed. Check otherdevices in this category. |
Description
Genuino Mega is with one of the richest versions in the series. The board contains an ATmega2560 microcontroller, equipped with 54 digital inputs/outputs, of which 15 can be used as PWM outputs (e.g. for controlling motors) and 16 analogue inputs. The circuit is clocked with a 16 MHz clock signal, has 256 kB of Flash memory and 8 kB of SRAM memory.
The subject of sale is an original Genuino product from the distributionwww.arduino.cc.
Main features
Below are some features that distinguish the modules from other programmable tiles.
| The name | Description |
|---|---|
|
Installed bootloader |
Thanks to the installed bootloader, the appropriateUSB cable andsoftware from the manufactureris sufficient to program the device. |
|
Shield |
The layout of connectors enables installation of dedicatedArduino Shieldcovers. |
|
Extracts . digital |
56 digital inputs/outputs enable, among other things, to control LEDs, relays and read button statuses. |
|
Performance Current |
The maximum current capacity of a single output is 20 mA. |
|
Outputs PWM |
15 PWM outputs allow e.g. for motor control and diode brightness adjustment. |
|
Inputs analogue |
The 16 inputs of the built-in 10-bit analogue-to-digital converter support, among others, sensors with analogue output. |
|
Communication serial |
The device supports popular communication interfaces, among others: UART, I2C and SPI. |
| Special functions | Some pins have special functions, a brief description of which is available in our guide. |
|
Memory Embedded |
Atmega2560 chip is clocked with 16 MHz signal, has 256 kB of flash memory, 4 kB EEPROM and 8 kB SRAM. |
|
Power supply DC connector |
Any power supplyfrom 7 V to 12 V with a 5.5 x 2.1 mm DC connector can be used to power Genuino. |
|
Power supply USB port |
The board can be powered from a computer viaa USB cable witha maximum current capacity of 500 mA. Genuino has a system that protects the socket against short circuits and excessive current flow. |
|
The connector is . ICSP |
The module has ICSP outputs to connect an externalAVR programmer. |
|
Pin IOREF |
The IOREF pin allows for direct access to the voltage with which the I/O outputs work. |
|
Built-in LED |
The connected LED on pin 13 allows debugging of simple programs. |
|
Output 3,3 V |
The built-in voltage regulator enables external devices to be supplied with 3.3 V with current consumption of up to 50 mA. |
|
First start-up In order to make it easier to start working with the module, we have prepareda guidewhich concerns the installation and first start-up of the environment. |
Layout of components on the Genuino Mega 2560 - in the latest version of the board, the reset button is located next to the USB port.
Specification
- Supply voltage: 7 V to 12 V
- Microcontroller: ATmega 2560
- Maximum clock frequency: 16 MHz
- SRAM: 8 kB
- Flash memory: 256 kB (8 kB reserved for bootloader)
- EEPROM memory: 4 kB
- Pins I/O: 54
- PWM channels: 15
- Number of analog inputs: 16 (A/C converter channels with 10 bits resolution)
- Serial interfaces: 4 x UART, SPI, I2C
- External interruptions
- Connected LED to pin 13
- USB A socket for programming
- 5.5 x 2.1 mm DC connector for power supply
|
Due to the conflict within the Arduino team, two versions of the environment were available to download from: Genuino tiles come from the distribution ofArduino.cc.If you install software downloaded from a source module other than the one described on the back of the module, you will receive a message about an unauthorized supplier of the board. You can cancel it with one click and the environment will work properly. |
Useful links |
