• EOL

NanoPi NEO v1.3 - Allwinner H3 Quad-Core 1,2GHz + 512MB RAM

Index: NNP-07028

Miniature computer NanoPi in version 1.3 Neo processor-Allwinner H3 quad-core ARM Cortex-A7 with a clock frequency of 1.2 GHz. Tile has a 512 MB DDR3 RAM, built-in Ethernet port and USB slot + 2 x USB Host on pins 2.54 mm, 36 GPIO, connector for memory card microSD. Works with manufacturer's systems u-boot and UbuntuCore.

NanoPi NEO v1.3 - Allwinner H3 Quad-Core 1,2GHz + 512MB RAM
€18.50
€15.04 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: FriendlyARM

 

Attention!

The sale of the product was completed. Check other devices in this category.

Description

Miniature computerNanoPiin versionNeo v1.3processor -Allwinner H3 quad-coreARM Cortex-A7 with a clock frequency of 1.2 GHz. Tile has512 MBof memoryDDR3, built-in portEthernetandUSB slot + 2x USB Host on pins 2.54 mm,36 GPIO, connector for memory cards microSD. Works with manufacturer's systems u-boot and UbuntuCore.

 


The advantage of tile is its small size, the dimensions of the tiles 40 x 40 mm.

What it takes to run minicomputer NanoPi?

The device has a USB slot and an Ethernet port and many others.

 

Operating system

NanoPi works with the systems selected by manufacturer: u-boot and UbuntuCore. The drive of the device can be a microSD card, which can be purchased in our store.

 

Operating systems can be downloaded fromthe manufacturer's website.

The manufacturer also providesguides around the installation of the system.

Communication

Minicomputer has communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors audio and video, the user has at his or her disposal:

  • 1x USB A connector + 2x USB Host on pins 2.54 mm, to which can be connected, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number usingan external USB HUB. The interfaces displayed on pins can be connected using wires.
  • Ethernet connector, that is the possibility to directly connect to the LAN.
  • GPIO x 36 pinoutputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers of engines. Among them are the pins supporting interfaces: I2C, SPI and UART. The pins have to be soldered individually,goldpin raster strips of 2.54 mmcan be purchased in our store.
  • a slot for microSDslot for memory cars microSD on which the operating system can be installed.

The distribution of the GPIO outputs - pins have to be soldered individually,goldpin raster strips of 2.54 mmcan be purchased in our store.

Power

As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage indicated on the port had a value of 5.0 and output current of the used adapter shall not be less than 2.0 A. In our assortment you will findpower supplies that meet these parameters, for example:power supply Extreme 2.1 A.

Radiator z taśmą termoprzewodzącą do NanoPi NEO

In our offer you will find alsospecial radiator.


 

Starter set

The manufacturer has prepareda set of sensors and modulesin a convenient chest that simplifies getting started with minicomputer.

Matrix Starter Kit - zestaw startowy dla NanoPi i Raspberry PiThe contents of the setMatrix Starter Kit- sold separately.

Specification

Model NanoPi Neo
Specification
Processor Allwinner H3
The core

Quad-Core ARM Cortex A7

Systems

u-boot

UbuntuCore

Clock frequency 1.2 GHz
RAM

512 MB

Memory

microSD memory card

GPIO socket

36-pin connector

for self-soldering

Power

5 V / 2 A - microUSB

Tile sizes 40 x 40 mm
Interfaces
USB-Host

1 x USB A socket

2 x USB Host on pins 2.54 mm

Network interface Ethernet 10/100 Mbps
Video -
Audio

audio output and microphone

out on the GPIO connector

Communication

UART, SPI, I2C, GPIO, PWM

The debugger

Serial port 4pin / 2.54 mm

Additional

Built-in led

 

 

UC - Microcontroller Allwinner H3
UC - Core Cortex A7
UC - RAM 512 MB
UC - core 4. Quad Core
UC - Digital pins 30
UC - External memory microSD card
UC - freq 1.2 GHz
UC - Ethernet yes
UC - USB 1x USB
UC - HDMI no
UC - I2C yes
UC - UART yes
UC - Connector 5V microUSB
UC - SPI interface yes
UC - LCD interface no
UC - Camera interface no
UC - Linux yes
UC - Android no
UC - Windows no
Package width 0.001 cm
Package height 0.001 cm
Package depth 0.001 cm
Package weight 0.001 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: