High-Power 18v15 - motor controller - module
High-Power 18v15 - motor controller - module
High-Power 18v15 - motor controller - module
High-Power 18v15 - motor controller - module
High-Power 18v15 - motor controller - module
High-Power 18v15 - motor controller - module - zdjęcie 1
High-Power 18v15 - motor controller - module - zdjęcie 2
High-Power 18v15 - motor controller - module - zdjęcie 3
High-Power 18v15 - motor controller - module - zdjęcie 4
High-Power 18v15 - motor controller - module - zdjęcie 5

High-Power 18v15 - single-channel 30V/15A motor controller - Pololu 755

Index: PLL-00744

Based on MOSFET transistors, the powerful H-bridge allows you to control the motor rotation in both directions. Motor power supply: from 5.5 V to 30 V. Maximum current: 15 A.

€36.98
€30.06 tax excl.

Available, 24h shipping!
(Check quantity)
Shipping in 24 hours
30-day returns
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Description: Pololu High-Power 18v15 - single-channel motor controller 30V/15A

A controller based on MOSFET transistors allows to control one DC motor supplied with voltage from 5.5 V to 30 V with current consumption up to 15 A.

The outputs are located on both sides of the module. One connector is located on each side of the module, which is responsible for the control and power supply of the logical part. On the opposite edge there are motor supply pins (V+, GND) and its outputs (OUTA, OUTB). The voltage value of the control signals should be between 3.5 V and 5.5 V. The manufacturer does not recommend working on 3.3 V.

In a standard application only the PWM signal and the DIR motor direction selector pin are required.Flags FF1 and FF2 signal incorrect operation of the system. The RESET pin is pulled up to power by default. When a low state is reached, the system will switch to the minimum power consumption state. All flags will also be reset.

The kit contains

  • Controller module
  • Electrolytic capacitor
  • Goldpin slat
  • ARK connectors

PIN Description
V+ Motor power supply (5.5V-30V). The output marked with + is the positive pole of the capacitor connection. The smaller V+ outputs allow you to monitor the motor power supply. Use for high currents is not recommended.
5V (out) 5V stabiliser output. Output current up to several mA. Be careful not to short-circuit the adjacent V+ pin as this leads to irreparable damage to the module.
GND The mass potential of the system.

OUTA

OUTB

DC motor outputs.
PWM Speed control signal. Default is in a low state
DIR Selection of the direction of engine rotation. In high state current flows from OUTA to OUTB. By default in float state.
RESET When low state is given, the system is in low power state. It also deletes all flags.

FF1

FF2

System state flags. In case of an error, a high state appears.
FF1 FF2 Description Blocked
outputs
L L No mistakes NO
L H Shortcut YES
H L Too high a temperature NO

H

H

Too low a voltage YES

Polol High-Power motor controller specification

  • Number of channels: 1
  • Motor supply voltage: 5.5 V to 30 V
  • Continuous current motor per channel: 15 A
  • Maximum PWM frequency: 40 kHz
  • Maximum voltage of the logical part 5.5V
  • MOSFET Transistor Resistance: 3.5 mΩ
  • Dimensions: 33 x 20.3 mm
  • Weight: 2.8 g (without connectors)
Voltage to 5.5 V
Voltage from 30.0 V
Current 15 A
Channels 1

Same day shipping

Posting the payment for the order on our account on a business day up to 10 AM means sending the goods on the same day!

The time of payment depends on the ELIXIR's hours session of the sender's bank and the recipient of the transfer. It may take up to 2-4 working days.

Free delivery for orders exceeding 300 PLN!

Only for prepaid orders shipped to Poland.

Terms of delivery outside of Poland

GLS - zone 1

Austria, Belgium, Croatia, The Czech Republic, Denmark, Germany, Netherlands, Slovakia

  • Delivery time: 2-4 days
  • Delivery cost: 35 PLN
  • Insurance: 5000 PLN
GLS - zone 2

Bulgaria, Estonia, France, Hungary, Italy, Latvia, Lithuania, Luxembourg, Portugal, Romania, Slovenia

  • Delivery time: 2-5 days
  • Delivery cost: 50 PLN
  • Insurance: 5000 PLN
Kurier GLS - zone 3

Finland, Greece, Ireland, Sweden, Cyprus, Malta, Spain

  • Delivery time: 2-7 days
  • Delivery cost: 80 PLN
  • Insurance: 5000 PLN

Terms of delivery in Poland

Card image cap
Poczta Polska
  • Delivery time: 1-3 days
  • Payment in advance: od 9,90 PLN
  • Cash on delivery: 17,90 PLN
  • Insurance: 1000 PLN
Card image cap
Kurier GLS
  • Delivery time: 1-2 days
  • Payment in advance: od 14,90 PLN
  • Cash on delivery: 22,90 PLN
  • Insurance: 6000 PLN
Card image cap
Paczkomaty 24/7
  • Delivery time: 1-3 days
  • Payment in advance: od 12,90 PLN
  • Over 8000 parcel lockers
  • Insurance: 200 PLN
  • Free delivery of orders over 300 PLN does not apply to parcels addressed outside of Poland.
  • The delivery period is counted in working days from the date of dispatch of the order.

Be the first to ask a question about this product!

No customer reviews for the moment.

You might also like

Pololu 37Dx52L Motor with 19:1 Gear 6V 500RPM

Polol's 499:1 gearbox motor generates 500 rpm, torque is 5.0 kg*cm (0.49 Nm). Powered from 6 V to 12 V, average current consumption is approximately 300 mA (max 5 A).
Index: PLL-00049
Index: PLL-00049
Unavailable
Regular price €24.42 Price €24.42
  • Free shipping

25Dx48L HP Motor with 4.4:1 Gear 6V 2220RPM - Pololu 1570

Polol's 4.4:1 gearbox engine generates 2150 rpm, torque is 1.5 kg*cm (0.14 Nm). Powered by 6 V, average current consumption is approximately 550 mA (max 6500 mA).
Index: PLL-00146
Index: PLL-00146
Available, 24h shipping!
(Check quantity)
Regular price €20.70 Price €20.70
  • Free shipping

DC motor - Micromotors HL149 with 21:1 transmission

HL149 DC motor with 21:1 geared motor. 0.075 Nm (0.76 kgcm) torque. Speed 160 rpm. Nominal supply voltage 6 V.
Index: MOT-00515
Index: MOT-00515
Unavailable
Regular price €3.70 Price €3.70
  • Free shipping

25Dx48L LP Motor with 4.4:1 Gear 6V 1300RPM - Pololu 1581

Polol's 4.4:1 gearbox engine generates 1280 rpm, torque is 0.6 kg*cm (0.05 Nm). Powered by 6 V, the average current consumption is approximately 250 mA (max 2400 mA).
Index: PLL-00743
Index: PLL-00743
Available, 24h shipping!
(Check quantity)
Regular price €18.58 Price €13.01
  • Free shipping
  • Reduced price
  • On sale

Customers who bought this product also bought:

MinIMU-9 v2 - accelerometer, gyroscope and magnetometer IMU I2C - Polol module

Sensor for measuring acceleration, magnetic field and angular velocity. It is a combination of a 3-axis accelerometer, magnetometer and gyroscope. It communicates via the I2C...
Index: PLL-00852
Index: PLL-00852
Unavailable
Regular price €9.07 Price €9.07
  • Free shipping

Simple High-Power 18v15 - USB 30V/15A motor driver - assembled - Pololu 1376

Easy to use single-channel direct current motor controller. It communicates through the USB port of the computer, UART TTL interface, analogue signal or RC radio interface....
Index: PLL-00522
Index: PLL-00522
Available, 24h shipping!
(Check quantity)
Regular price €48.60 Price €38.88
  • Free shipping
  • Reduced price
  • On sale

Mini Maestro USB 12-channel servo driver - Pololu 1352

12-channel servo controller with digital and analog signals. The user can control the servers via: PC (USB) application, serial interface and simple scripting language.
Index: PLL-00068
Index: PLL-00068
Available, 24h shipping!
(Check quantity)
Regular price €27.79 Price €27.79
  • Free shipping

A kit Raspberry Pi model B - Basic

The kit includes the Raspberry Pi model B and a set of components necessary to run and use the minicomputer: housing, memory card with system, HDMI cable, 1.5 A power supply,...
Index: RPI-01514
Index: RPI-01514
Unavailable
Regular price €59.30 Price €59.30
  • Free shipping

Breadboard - 830 holes

Breadboard is used for creating and testing electronic circuits without the need for soldering. Version with 830 holes, the size of 165 x 53 mm. Stripes (blue and red) help in...
Index: PLY-00055
Index: PLY-00055
In stock, shipping 24 hours!
(Check quantity)
Regular price €1.79 Price €1.79
  • Free shipping

Transistor N-MOSFET IRL540NPBF - THT - 5pcs

Vds: 100 V Id: 36A. Rdson: 0,044 Ohm. Case: TO-220. Items are sold in sets of 5 pieces.
Index: UCC-00127
Index: UCC-00127
In stock, shipping 24 hours!
(Check quantity)
Regular price €3.47 Price €3.47
  • Free shipping

N-MOSFET BUZ11A - THT

N-MOSFET BUZ11A transistor with voltage 50 V and the Id current 26 A . The maximum power is 75 W . It was locked in a TO-220 housing.
Index: UCC-00732
Index: UCC-00732
Waiting time: about 10-30 days
Regular price €0.63 Price €0.63
  • Free shipping

Microphone 50-56dB 9/4,5mm - THT - 10 pcs.

Height h: 4.5 mm. Diameter Ø: 9 mm. Sensitivity: 36-38 dB. Pins for soldering to  the printed circuit board.
Index: UCC-00740
Index: UCC-00740
In stock, shipping 24 hours!
(Check quantity)
Regular price €1.56 Price €1.56
  • Free shipping

DRV8825 - stepper motor driver 45V / 2,2A - Pololu 2133

Stepper motor's driver based on the system DRV8825, allows you to control the motor with a current consumption of up to 1.5 A (with cooling up to 2.2 A) per coil, when...
Index: PLL-01324
Index: PLL-01324
In stock, shipping 24 hours!
(Check quantity)
Regular price €8.12 Price €8.12
  • Free shipping

ARK4 connector for breadboard

Connector ARK4 connect wires to the breadboard with screw connectors. Suitable for standard breadboards available in our store.
Index: MOD-01469
Index: MOD-01469
In stock, shipping 24 hours!
(Check quantity)
Regular price €1.02 Price €1.02
  • Free shipping

Supply module for contact plates MB102 - 3,3V 5V

Power module for breadboard, it allows for connection of power supply of 5 V or 3.3 V using the AC adapter. It has LED indicating the power connection.
Index: MOD-01482
Index: MOD-01482
In stock, shipping 24 hours!
(Check quantity)
Regular price €1.37 Price €1.37
  • Free shipping

Electret microphone and OPA344 amplifier module - SparkFun BOB-12758

Module with microphone and operational amplifier. The output signal is amplified 100 times so the system can be connected directly to the analog inputs of microcontrollers.
Index: SPF-01614
Index: SPF-01614
Czas oczekiwania: ok. 10-30 dni
Regular price €7.65 Price €7.65
  • Free shipping

Products from the same category

JRK G2 18v19 - single channel USB driver with 30V / 19A feedback - Pololu 3146

Extremely easy to use motor controller with feedback. Communication interfaces available: USB, TTL, I2C, analog and radio. Power supply voltage is 6.5 V to 30 V and continuous...
Index: PLL-12103
Index: PLL-12103
Waiting time approx. 4-6 weeks
Regular price €83.49 Price €83.49
  • Free shipping

JRK G2 18 v 19 - single channel USB driver with 30V / 19A feedback - Pololu 3147

Extremely easy to use motor controller with feedback. Communication interfaces available: USB, TTL, I2C, analog and radio. Power supply voltage is 6.5 V to 40 V and continuous...
Index: PLL-12107
Index: PLL-12107
Waiting time approx. 4-6 weeks
Regular price €83.49 Price €83.49
  • Free shipping

JRK G2 24v21 - single channel USB driver with 40V / 21A feedback - Pololu 3149

Extremely easy to use motor controller with feedback. Communication interfaces available: USB, TTL, I2C, analog and radio. Power supply voltage is 6.5 V to 40 V and continuous...
Index: PLL-12124
Index: PLL-12124
Waiting time approx. 4-6 weeks
Regular price €127.67 Price €127.67
  • Free shipping

RoboClaw 2x45A USB V5 - two-channel 34V / 45A engine controller - Pololu 2397

Two-channel DC motor controller. It communicates via microUSB port, UART TTL protocol, analogue signal or RC radio interface. Power supply voltage is from 6 V to 34 V....
Index: PLL-05569
Index: PLL-05569
Waiting time approx. 10-21 days
Regular price €246.51 Price €246.51
  • Free shipping

RoboClaw 2x7A USB V5B - two-channel 34V / 7.5A engine controller - Pololu 3284

Two-channel DC motor controller. It communicates through the microUSB port, UART TTL interface, analogue signal or RC radio interface. Power supply voltage is from 6 V to 34 V....
Index: PLL-05571
Index: PLL-05571
Waiting time approx. 10-21 days
Regular price €99.77 Price €99.77
  • Free shipping

RoboClaw 2x30A USB V5 - two-channel 34V / 30A engine controller - Pololu 2396

Two-channel DC motor controller. It communicates via microUSB port, UART TTL protocol, analogue signal or RC radio interface. Power supply voltage is from 6 V to 34 V....
Index: PLL-05573
Index: PLL-05573
Waiting time approx. 10-21 days
Regular price €169.53 Price €169.53
  • Free shipping

Qik 2s9v1 Dual Serial Motor Controller - Pololu 1110

Two-channel DC motor controller allowing to control the speed and direction of motor rotation using a simple serial interface, enabling simple connection of the controller to a...
Index: PLL-13730
Index: PLL-13730
Waiting time about 10-30 days
Regular price €23.02 Price €23.02
  • Free shipping

RoboClaw ST 2x45A USB V5 - two-channel 34V / 45A engine controller - Pololu 2398

Dual-channel driver for DC motors. Communicates via the microUSB port, UART TTL protocol, analog signal or RC radio interface. The supply voltage ranges from 6 V to 34 V.The DC...
Index: PLL-05439
Index: PLL-05439
Czas oczekiwania ok. 10-21 dni
Regular price €237.19 Price €237.19
  • Free shipping

MC33926 - dualchannel motor driver 28V/3A - shield for Raspberry Pi 3/2/b+ - assembled - Pololu 2756

Module with dual MC33926 driver of motors, working with voltages from 5 V to 28 V and current up to 3 A per channel (max. 5 A). The shield can be linked directly with...
Index: PLL-04346
Index: PLL-04346
Czas oczekiwania ok. 10-21 dni
Regular price €27.67 Price €27.67
  • Free shipping

Dual TB9051FTG Motor Driver for Raspberry Pi (Partial Kit) - Pololu 3142

Extremely easy to use motor controller with feedback. Communication interfaces available: USB, TTL, I2C, analog and radio. Power supply voltage is 4.5 V to 28 V and continuous...
Index: PLL-12436
Index: PLL-12436
Available, 24h shipping!
(Check quantity)
Regular price €45.35 Price €45.35
  • Free shipping

TLC5940 - controller, PWM generator - SparkFun BOB-10616

16-channel PWM signal generator. It communicates via the SPI bus. It can be used as an LED driver, the controller of revolutions of the DC motors and the servo controller.
Index: SPF-01856
Index: SPF-01856
In stock, shipping 24 hours!
(Check quantity)
Regular price €17.19 Price €17.19
  • Free shipping

TReX Dual Motor Controller DMC02 - Pololu 767

A smaller version of the TReX controller. Used for small motors. It has a current capacity of up to 13 A for each motor. Allows you to control motors through a serial...
Index: PLL-06715
Index: PLL-06715
Waiting time approx. 10-21 days
Regular price €48.81 Price €48.81
  • Free shipping