• EOL

Arduino Industrial 101 - WiFi + Ethernet

Index: ARD-06361 EAN: 8058333492230

Advanced module created on the basis of Arduino Yun allows to program and control the device wirelessly through WiFi network. It is based on two microcontrollers: Atheros AR9331 MIPS 400MHz with Linux and ATmega32u4, which has 32 kB of flash memory, 2.5 kB of RAM, 20 digital inputs/outputs of which 7 are PWM and 12 analog inputs and interfaces, including USB and Ethernet.

Arduino Industrial 101 - WiFi + Ethernet
€43.90
€35.69 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Arduino

Attention!

The sale of the product has been completed. Check otherdevices in this category.

Description

Advanced module created on the basis ofArduino Yunallows to program and control the device wirelessly through WiFi network. It is based on two microcontrollers:

  • Atheros AR9331with MIPS 400 MHz architecture with Linux, which controls WiFi, Ethernet and USB connection.
  • ATmega32u4- equipped with 20 digital inputs/outputs, 7 of which can be used as PWM outputs (e.g. for controlling motors) and 12 as analogue inputs. The system is clocked with a 16 MHz clock signal, has 32 kB of Flash memory and 2.5 kB of SRAM memory.

Arduino Industrial 101 - WiFi + Ethernet

Arduino Industrial 101 does not have solderable joints, however, they are available in a self-assembly kit. The user decides which sockets he needs, so he can keep the smaller dimensions of the board.

Main features

Below we present some features that distinguish Arduino modules from other programmable tiles.

The nameDescription

Installed

bootloader

Thanks to the installed bootloader, the appropriatemicroUSB cable andsoftware from the manufacturer is sufficient to program the device.

Connection

WiFi

Arduino Industrial can easily, wirelessly, via WiFi network, program, configure or change and read output states.

Ethernet

This version has an Ethernet controller on GPIO pins.

Arduino

Shield

The layout of connectors enables installation of dedicatedArduino Shieldcovers.

Extracts .

digital

20 digital inputs/outputs enable, among others, to control LEDs, relays and read button states.

Performance

Current

The maximum current capacity of a single output is 40 mA.

Outputs

PWM

7 PWM outputs allow e.g. for motor control and diode brightness adjustment.

Inputs

analogue

The 12 inputs of the built-in 10-bit analogue-to-digital converter support, among others, sensors with analogue output.

Communication

serial

The device supports popular communication interfaces, among others: UART, I2C and SPI and USB.
Special functions Some pins have special functions, a brief description of which is available in our guide.

The socket .

USB A

The board has a built-in USB controller, which is connected to a USB type A computer socket.

Two microcontrollers

  • Atmega32u4is clocked with 16 MHz signal, has 32 kB of Flash 1 kB EEPROM and 2.5 kB SRAM.
  • Atheros AR9331with MIPS archietecture is clocked with 400 MHz signal. It has 16 MB. There is a Linux OpenWRT Linino system on board.

5 V power supply

microUSB

You can usea5Vpower supply unitwith microUSB connector to power Arduino.

Power supply

USB port

You can power the board from your computer viathe microUSB cable,whilekeeping in mindthat the maximum current capacity of the USB port is 500 mA. Arduino has a system that protects the socket against short circuit and too high current flow.

The connector .

ICSP

The module has ICSP outputs to connect an externalAVR programmer.

Pin

IOREF

The IOREF pin allows for direct access to the voltage with which the I/O outputs work.

Built-in

LED

The connected LED on pin 13 allows debugging of simple programs.

Output

3,3 V

The built-in voltage regulator enables external devices to be supplied with 3.3 V with current consumption of up to 50 mA.

Arduino Industrial 101

ArduinoIndustrial 101 - distribution of elements on the board.

Specification .

  • Power supply voltage: 5 V from microUSB port
  • AVR Microcontroller: ATmega32u4
    • Maximum clock frequency: 16 MHz
    • SRAM: 2.5 kB
    • Flash memory: 32 kB (4 kB reserved for bootloader)
    • EEPROM memory: 1 kB
    • Ports I/O: 20
    • PWM outputs: 7
    • Number of analog inputs: 12 (A/C converter channels with 10 bits resolution)
    • Serial interfaces: UART, SPI, I2C
    • External interruptions
  • Linux processor: AtherosAR9331
    • Architecture: MIPS400 MHz
    • Power supply voltage: 3,3 V
    • Ethernet IEEE 802.3 10/100 Mbit/s
    • IEEE 802.11b/g/n WiFi
    • RAM: 64 MB DDR2
    • Flash memory: 16 MB
  • USB socket Type-A 2.0

Programming

Programming Arduino Industrial 101 is as simple as other modules in this family. Just download and install Arduino IDE from the manufacturer's website and then select Arduino Industrial 101 from the tool menu. ATmega32u4 can also be programmed using ICSP connector viaAVRprogrammer, like UBSasp.

Arduino Ciao

Modern technology that easily allows Arduino tiles to communicate with the outside world IoT. The library aims to simplify the connection between ATmega32u4 and Linux Linino.

A diagram of the Arduino Ciao library.

UC - Microcontroller ATmega328
UC - Core 8-bit AVR
UC - EEPROM 1 kB
UC - Flash 32 kB
UC - RAM 2,5 kB
UC - Digital pins 20
UC - analog in 12
UC - freq 16 MHz
UC - A/C 10-bit
UC - PWM 7
UC - WiFi yes
UC - USB microUSB
Package width 0.001 cm
Package height 0.001 cm
Package depth 0.001 cm
Package weight 0.001 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: