TB67S279FTG - Stepper Motor Driver 47V/1,1A - with holders - Pololu 3099

Index: PLL-13681 EAN: 5904422321178

Stepper motor driver based on the chip TB67S279FTG. Powered by a voltage range from 10 V to 47 V, with a maximum current consumption of 2 A per coil. Maximum resolution: 1 / 32 step. By using the TB67S279FTG driver, the chip can dissipate more heat which allows 1.1 A current flow without a heat sink. The module has soldered connectors.

TB67S279FTG - Stepper Motor Driver 47V/1,1A - with holders - Pololu 3099
€13.50
€10.98 tax excl.
Waiting time: 4-6 weeks
Only on request
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Product description: TB67S279FTG - 47 V / 1,1 A stepper motor driver - with connectors - Pololu 3099

The circuit allows to control a stepper motor with a device that allows to generate logic states, e.g. Arduino.Arduino,STM32Discovoery,Raspberry Pior anymicrocontroller. Pololu module is characterized by very simple operation. Rising edge of each impulse on CLK (STEP) pin corresponds to one step. Selection of the direction is performed by giving the appropriate state to the CW/CCW (DIR) pin (e.g. low state - clockwise rotation, high state - anticlockwise rotation). The driver can also select theresolution ofmotor operation.

The module has soldered goldpin connectors. We offer alsoversion without connectors.

TB67S279FTG - sterownik silnika krokowego 47V/1,1A - ze złączami - Pololu 3099

TB67S279FTG - 47 V / 1.1 A stepper motor driver - with connectors - Pololu 3099.

Minimum wiring diagram to connect microcontroller to TB67S2x9FTG.

The controller requires a supply voltage from 10 V to 47 V, which will be connected to VIN and GND terminals.

Connecting the controller

To control a bipolar stepper motor, connect the circuit as shown below.

Power supply

To supply the logic part of the module a voltage of 5 V is required.VDD PIN. Motor supply voltage from 10 V to 47 V is applied to pinVIN PIN.

Caution!

Connecting and disconnecting the motor while the controller is on can damage the system.

Resolution

The step size is selected using DMODE0, DMODE1, DMODE2 inputs. The possible settings are shown in the table below. The MS1, MS2 and MS3 inputs have an internal pull-down resistor (100 kΩ).

MS1 MS2 MS3 Resolution
low low low Standby mode
low low high Full step
low high low Non-wheeling half step ('a')
low high high 1/4 step
high low low circular half step ("b")
high low high 1/8 step
high high low 1/16 step
high high high 1/32nd step
TB67S279FTG - sterownik silników krokowych

TB67S279FTG - 47 V / 1.1 A stepper motor driver - with connectors - Pololu 3099.

Controlling

The rising edge of each pulse on the CLK (STEP) pin corresponds to one step. Selection of the direction is done by giving the appropriate state on the CW/CCW (DIR) pin (e.g. low state - clockwise rotation, high state - anticlockwise rotation). Ifthe motoris to rotate in one direction only, the DIR pin can be left unplugged.

When the RESET pin goes high, the driver resets its state in the translator array, which outputs to the initial value of 45°. This corresponds to 100% of the current limit on both coils in full step and non-wheel half step modes. The RESET pin does not disable the motor outputs, the controller will continue to supply current to the motor but will not give information to the CLK output

The TB67S2x9FTG can detect several error conditions that report causing one or both LO pins to be low. The manufacturer has includeda table of error combinations on the LO1 and LO2 pinsin thedocumentation.

A detailed description of each pin can be found on themanufacturer's website.

Voltage to 10.0 V
Voltage from 47.0 V
Current 1.1 A
Channels 1
Package width 8 cm
Package height 1 cm
Package depth 8 cm
Package weight 0.004 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: