Air quality / dust sensor PM1.0 / PM2.5 / PM10 - PMS3003 - 5 V UART and PWM

Index: PLA-18880 EAN: 5904422366339
Air cleanliness sensor allows for measurement of suspended particles PM1.0, PM2.5 and PM10. The sensor which the module is equipped with allows to detect particles with diameter above 0,3 μm. The chip is powered by 5 V, the logic voltage is 3.3 V, the module communicates through the UART and PWM interface.
Air quality / dust sensor PM1.0 / PM2.5 / PM10 - PMS3003 - 5 V UART and PWM
€13.01 tax excl.
Discontinued product
30-day returns
PayPal payment
Manufacturer: PlanTower


The product has been discontinued. Check other products in category.

Product description: Air cleanliness sensor PM1.0 / PM2.5 / PM10 - PMS3003P - 5V UART and PWM

Theair cleanliness sensor allows for measurement of suspended particlesPM1.0, PM2.5andPM10. Thesensorequipped with the module allows to detect particles with a diameterabove 0.3 μm. The chip is powered by 5 V, the logic voltage is 3.3 V, the module communicates through theUARTandPWMinterfaces.

The sensor works based on a laser chip. A fan sucks air through the inlet, then the sensor takes a measurement as the particles pass through the laser beam, so the light source is covered and the differences in light are analysed by the detector and converted to a digital signal.

Czujnik czystości powietrza PMS3003P

Air purity sensor PMS3003P.

Zastosowanie PMS3003P

Application of PMS3003P sensor.

Application and installation of PMS3003P.

The PMS3003P PM1.0 / PM2.5 / PM10 - 5V UART and PWM air purity sensor is perfect for measuring the quality of air indoors, but the wide temperature range in which it can work(from -10°C to 60°C) also allows its use outdoors (after applying the appropriate housing).

Its small size allows easy integration into a project and integration with the target device's casing. When designing, it is important to ensure undisturbed air flow both on the inlet side and at the outlet duct. The module has two mounting holes for simple and robust fixing.


  • PMS3003P sensor
  • Connection cable


The sensor is equipped with 8 pins, which description can be found in the table.

Pin 1 VCC - 5V power supply.
Pin 2 Device ground.
Pin 3 SET pin.
Pin 4 RXD - UART receiver Operates at 3.3 V.
Pin 5 TXD - UART transmitter. Operates with a voltage of 3.3 V.
Pin 6 Reset. Operates with a voltage of 3.3 V.
Pin 7 Not connected.
Pin 8 PWM output.

The device operates with a voltage of 3.3 V, to connect to a device operating with a higher voltage we recommend using avoltage converter.

PMS3003P air quality module

PMS3003P air quality sensor is based on an optical (laser) method for measuring the content of particulate matter. Laser light falling on particles flying through the measurement chamber is scattered and detected by the built-in photodetector. The signal from the photosensitive element is then amplified, filtered and analysed by the internal processor.

The PMS3003P module has an 8-pin connector, providing the user with both power rails (GND and +5V), as well as a control pin (SET), a reset line (RESET) and the input and output of the UART interface (RXD, TXD) and PWM. Importantly, the sensor is designed to work with microcontrollers with I/O line voltages up to 3.3V. When connecting to 5-volt systems (e.g.Arduino), a logic level converter should be used.


  • Supply voltage: 5 V
  • Logic voltage: 3,3 V
  • Current consumption: 100 mA
  • Idle consumption: 200 µA
  • Measuring range
    • 0.3 µm to 1.0 µm
    • 1.0 µm to 2.5 µm
    • 2.5 µm to 10 µm
  • Response time: up to 10 s
  • Operating temperature: from -10 °C to 60 °C
  • Board dimensions: 50 x 43 21 mm
  • Weight: 36 g
Moduł jakości powietrza PMS3003P

Module is based on optical measurement method.

Voltage to 5.0 V
Voltage from 5.0 V
UC - Microcontroller W600
Package width 7 cm
Package height 1.9 cm
Package depth 10 cm

Same-day shipping

  • Crediting the payment for the order on our account on a business day before 10:00 AM means sending the goods on the same day.
  • All packages are being delivered by GLS Group courier and covered with insurance up to 1200 EUR.
  • You will receive a link to track your package and monitor the progress of delivery as soon as it is shipped.

Terms of delivery 

GLS - zone 1

Austria, Belgium, Croatia, The Czech Republic, Denmark, Germany, Netherlands, Poland, Slovakia 

  • Delivery time: 2-4 days
  • Delivery cost: from 4.18 EUR
  • Insurance: 1200 EUR
GLS - zone 2

Bulgaria, Estonia, France, Hungary, Italy, Latvia, Lithuania, Luxembourg, Portugal, Romania, San Marino, Slovenia

  • Delivery time: 2-5 days
  • Delivery cost: from 5.35 EUR
  • Insurance: 1200 EUR
GLS - zone 3

Finland, Greece, Ireland, Spain, Sweden 

  • Delivery time: 2-7 days
  • Delivery cost: from 7.67 EUR
  • Insurance: 1200 EUR

Payment methods

Card image cap
  • Botland is a PayPal verified seller. Protect your financial information with this fast, safe and secure online payment system.

Card image cap
  • Choose easy and quick PayU e-payment method. Your financial information will stay secure.

Customers who bought this product also bought:

Products from the same category: