- EOL
|
Attention! The product has been discontinued. Check other products in category. |
Product description: Grove Creator Kit - β - 30 Grove modules for Arduino
Set of 30 modules and cables with Grove interface. The Creator Kit is designed for everyone, regardless of age or level of advancement. All modules included in the kitwork with ArduinoandArduino compatible tiles using the appropriate Grove Base Shield overlay(not included). The kit also includesa user guide withsample projects and programs.
The content of the set has been closed in a convenient container.
|
Attention! The set does not include ArduinoandBase Shield overlay.They can be purchased separately in our shop. Base Shield overlay is not required, but it makes it easier to use the modules. |
Grove system
Grove is a4-pin connector (power, ground and signal) to connect modules with a base plate for Arduinoor RaspberryPi. This system allowsquick and easyconnection of modules to the base plate without fearof bad connection, themountingsystem itselfresembles Lego blocks.When usingmodules with this interface, you can use the appropriate cable andSeeeduino motherboard orBase Shield overlay for Arduino.
Main features of the Creator Kit
- Compatibility with Arduino Uno
- Rich handbook
- Handy organizer
- Numerous examples and guides
- Perfect for a gift
- No soldering required
The main advantage of the Grove system is the unification of connectors. In practice, this means that if the number of modules in a set is insufficient, it is possible to choose from a widerange of Grove, any othersensor and connect it to the base plate using dedicatedGrove cables.
30 Grove modules set - Creator Kit γ.
|
Compatible with Arduino, RaspberryPi andmicro:bit. A user guide for Arduino users is included, but the modules also work with other platforms. |
User's guide
The set comes with a rich instructional and sample code guide in the form of over 100 pages of book. The guide will guide you through the whole Arduino IDE installation process and show you how to connect and program the module step by step.
Grove Creator Kit user guide.
| The manual is also available for download inPolish. |
Set contents
There are 30 elements in the set, the description of individual modules is available in the table.
| L.p. | Photo | Description |
|---|---|---|
| 1 |  |
NTC analog temperature sensor- analogsensor compatible with Arduino and Raspberry Pi. Powered from 3.3 V to 5 V. Can measure temperature from -40 °C to 125 °C with an accuracy of 1,5 °C. |
| 2 |  |
Slide switch module- a moduleequipped with a slide switch. Powered from 3.3 V to 5 V. |
| 3 |  |
38kHz 940nm IR receiver-infraredreceiveroperating at 38 kHz with voltage from3.3 V to 5.0 V. |
| 4 |  |
940nm IR transmitter- infrared transmitteremittinglight at 940nm wavelength. It works withvoltage from 3.3 V to 5.0 V. The sensor transmits a signal over a distance of up to 10 m. |
| 5 |  |
Mini PIR motion detector- detection ofan object is signaled digitally - high state on the SIG pin. The range of the detector is 2 m. |
| 6 |
|
10kΩ linear rotary potentiometer - top connector -10kΩlinear rotarypotentiometer. It has a rotation range of300°. |
| 7 |  |
Ultrasonic distance sensor 3-350 cm- ultrasonic sensoroperating in the range from 3 cm to 350 cm. Powered by 5 V. |
| 8 |  |
2x16 I2C white-blue LCD display with backlighting-2 x 16 charactersmonochromeLCD display with high brightness backlighting. |
| 9 |  |
Thumb Joystick with push-button - a module with a board- a moduleequipped with a joystick similar to analog devices used e.g. in game controllers. It has the ability to detect movements in two directions and a button, activated by pressing the knob. |
| 10 |  |
LM386 sound sensor- modulebased on LM386 chip and electret microphone. It can be powered from 4 V to 12 V. |
| 11 |  |
DHT11 temperature and humidity sensor. The output isadigital signal. The measuring range for temperatureis from 0°C to 50°C andhumidity from20% to 90%RH. |
| 12 |  |
Relay module v1.2-allows to control actuators by cutting off or supplying power. For proper operation it requires a 5 V power supply and a digital control signal supply. |
| 13 |  |
Multi-coloured LED- a module with an LED that can emit light in many applause. |
| 14 |  |
Tilt sensor- simple tilt sensor with digital output. It is powered from 3.3 V to 5 V. |
| 15 |  |
LM358 ambient light intensity sensor v1.2- the sensorallows to detect the light intensity and reflects the analog voltage signal back to Arduino. The light range is from 1 lux to 350 lux. Power supply voltage is 5 V. |
| 16 |  |
RGB LED v2.0 - a module with RGB diode-allows you to control the RGB diode using digital pins of the microcontroller. |
| 17 |  |
Precipitation/water sensor -a sensorused to detect the presence of water or its quantity. It is powered by 5 V. |
| 18 |  |
SW-420 Vibration sensor- whenthe sensor is at standstill, the output is given a constant high signal and changes to low when vibration is detected. The sensitivity can be adjusted by means of a potentiometer located on the board. |
| 19 |  |
Push Button with backlight - yellow- mhas a button with a yellow LED.Powered by 3.3 V to 5 V. |
| 20 |  |
Push Button with illumination - red- module equipped with a button with a red LED. Powered by 3.3 V to 5 V. |
| 21 |  |
Push Button with illumination - blue- module equipped with a button with a blue LED. Powered by 3.3 V to 5 V. |
| 22 |  |
Module with active buzzer- the moduleemitsa steady tone when the high state is given. When using the PWM it can generate different sounds and effects. |
| 23 |  |
RS-06WD reflective sensor v1.1- moduleequipped with RS-06WD reflective sensor.Itconsistsofan infrared light emitting diode and a high-sensitivity phototransistor. It is powered by 5 V. |
| 24 |  |
Magnetic switch- the sensorcan be activated by means of an electromagnet or permanent magnet.Powered by 5 V. |
| 25 |  |
Push button module-has a built-in tact-switch and pull-down resistor. |
| 26 |  |
Module with blue LED- modulewith blue LED. The LED starts to light up when the signal pin is switched to high. In addition, a potentiometer to control the LED brightness has been placed on the board. |
| 27 |  |
Module with red LED- the LED starts to light up when the signal pin is switched to high. Additionally, a potentiometer to control the brightness of the diode has been placed on the board. |
| 28 |  |
Module with green LED- module with green LED. The LED starts to light up when the signal pin is switched to high. In addition, a potentiometer to control the LED brightness has been placed on the board. |
| 29 |  |
LM2904 sound sensor- modulebased on LM2904 chip and microphone. It can be powered from 3.5 V to 10 V. The output is an analogue signal. The sensor allows to detect the strength of ambient sound. |
| 30 |  |
Sensor / probe for soil moisture measurement - analogue- ca sensor for determining the soil moisture level. It is powered from 3.3 V to 5 V. The output is an analogue voltage, which increases in value as the humidity increases. |
| 31 |  |
Grove cable set -cables terminated with Grove - Grove plug, Grove - female cable and Grove - male cable. |
| 32 |  |
User guide - a manual with sample connection diagrams and programs. |
| We also recommend other sensors and modules from the Grove series. |
Video
The manufacturer also provides video guides in English version.
Useful links |
