16-channel relay module with optoisolation - 10A / 250VAC contacts - 12V coil

Index: MOD-06941 EAN: 5904422359928

The module is equipped with sixteen JQC3F-12VDC-C relays with a 12-volt coil with optoelectronic isolation. The system allows you to control the actuators using the microcontroller ports or any set of starters.

16-channel relay module with optoisolation - 10A / 250VAC contacts - 12V coil
€13.50
€10.98 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: OEM

Product description: 16-channel relay module with optoisolation - 10 A / 250 V AC contacts - 12 V coil.

The module allows you to control actuators consuming up to 10 A by means of microcontroller ports or any startup kit. Opto-isolation separates the control signal from the part related to the relay power supply, thus ensuring safe operation of the control system.

Connection

For proper operation, simply connect the relay coil power supply and the digital control signal. The leads are standard 2.54 mmgoldpin strips, which allow connection with popularconnection cables.

The relay has the following leads

  • 5V- optoisolator power supply
  • GND- system weight
  • IN1 ... IN16- control inputs of relays, switched on in low state
  • KF (ARK) connectors- relay contacts, connected according to the drawing on the module board.

Examples of application

  • Lighting controller
  • Controller of actuators
  • Switch for electrical equipment, including motors

Specification

  • VCC supply voltage: 12 V
  • Attached in a low state
  • Current consumption of each input: approx. 60 mA
  • Relay JQC3F-12VDC-C (documentation)
    • Coil voltage: 12 V
    • Maximum contact voltage: 250 VAC, 110 VDC*.
    • Maximum current: 10 A
  • Optoelectronic isolation
  • 16 LEDs indicating vh activation of relays
  • Plate dimensions 177 x 80 mm
  • Weight: 225 g
  • Diameter of mounting holes: 3 mm

* The maximum contact voltage is dependent on the type of load - see thedocumentationin Table 7. Contact Rating.

Channels 16
Interface Digital I / O
Package width 15 cm
Package height 2 cm
Package depth 22 cm
Package weight 0.216 kg

Józef

07/24/23

Question: Hello I have this module, but I have a problem after switching the switch I have a terribly small voltage on the race. what is caused by this I supply 5V so the output should be 12 yes?
Answer: The module is powered by 12 V. A voltage of up to 250 VAC should be applied to the COM connector, a voltage equal to the voltage applied to COM will appear on the NO/NC connectors when the relay state is switched. Relays are controlled by a low state (applying 0V / GND to the IN connector will switch the relay).
Łukasz

01/23/23

Question: Hello, I bought from you a relay module 16 channels with optoisolation - contacts 10A/250VAC - coil 12V and I would need to buy for it a remote control which I can use so that each channel is activated separately?
Answer: Unfortunately, the module with relays does not have a built-in radio chip for remote control. The module can be connected to a microcontroller such as an Arduino module along with a radio module and programmed accordingly.
https://botland.com.pl/439-arduino-seria-podstawowa-oryginalne-plytki
https://botland.com.pl/105-moduly-radiowe

Product reviews

16-channel relay module with optoisolation - 10A / 250VAC contacts - 12V coil

4.9/5

Average grade

8

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Zdjęcia użytkowników

Customers who bought this product also bought:

Products from the same category: