- New
- Sale
- Sale
- Reduced price
- Sale
- Reduced price
- Sale
- Reduced price
- Sale
Arduino Grove series - Strona 2
Loading...
Grove - ProtoShield - prototype board
Prototype board Grove with a soldered socket. It allows for an easy access to four lines of a standard Grove-S0, S1, VCC and GND series connection cable. The layout of the...
Index: SEE-11344
Index: SEE-11344
Grove - a speaker with a digital interface
Speaker module Grove is a device controlled by the PWM signal. It c an work as a simple buzzer or audio player. The volume is adjustable with the built in potentiometer. The...
Index: SEE-11352
Index: SEE-11352
I2C hub allows you to connect several modules to one I2C bus connector on Base Shield v2 board. Using splitter you can connect 7 sensors from Grove series to one socket.
Index: SEE-04438
Index: SEE-04438
Grove - IR receiver 38kHz 940nm
IR receiver from Grove , operating at a frequency of 38 kHz with a supply voltage from 3.3 V to 5.0 V. Maximum sensitivity is observed for the wave length of 940 nm.
Index: SEE-04419
Index: SEE-04419
Grove Shield for Raspberry Pi Pico - Seeedstudio 103100142
Grove frontend for Raspberry Pi Pico module . Converts Pico GPIO connectors to Grove type connectors such as I2C, UART and digital and analog ports. It allows you to...
Index: SEE-18902
Index: SEE-18902
Grove - capacitive humidity sensor - corrosion resistant
The device is used to measure the soil moisture by the capacitive detection. It has a built in voltage regulator which provides an operating voltage in the range from 3.3 V to...
Index: SEE-13967
Index: SEE-13967
Grove - set of 5 female-female 4-pin - 2mm/30cm with latch
A set of five 4-pin Grove wires. They are used to connect sensors with Grove Base Shield v2. Cable length is 30 cm. Version with a latch.
Index: SEE-04398
Index: SEE-04398
Grove - LoRa-E5 STM32WLE5JC - EU868/US915 - LoRaWAN radio module - Seeedstudio 113020091
LoRa-E5 radio module with Grove connector, manufactured by Seeedstudio. It features an STM32WLE5JC chip with a low-power 32-bit ARM Cortex M4 processor with a clock...
Index: SEE-19265
Index: SEE-19265
Grove - 10kΩ rotary potentiometer linear lower connector
Potentiometer 10 kOhm with linear rotary. It has a 300° range of rotation. It has a 4-pin Grove connector on the other side of the handle. The kit includes a cable adapted...
Index: SEE-04430
Index: SEE-04430
Grove - Base Hat for Raspberry Pi - shield for Raspberry Pi 4B/3B+/3B
Overlay for Raspberry Pi 4B / 3B+ / 3B based STM32 microcontroller with 12-bit ADC, with Grove connectors, allows the connection of sensors and modules from the Grove...
Index: SEE-15458
Index: SEE-15458
Grove - Shield for micro:bit v2.0
Grove Shield v2.0 overlay for micro:bit features 4 4-pin connectors for easy connection of Grove series sensors to the minicomputer.
Index: SEE-14132
Index: SEE-14132
Grove - GSR sensor - electrical resistance of the skin
Module from the Grove series equipped with GSR sensor using the galvanic-skin reaction. It is powered with the voltage of 3.3 V or 5V. The s ensors of this type are used in...
Index: SEE-11314
Index: SEE-11314
Grove - temperature and humidity sensor DHT11 - Seeedstudio 101020011
The sensor of temperature and humidity DHT11 from the Grove series. The output is a digital signal. The temperature measurement range is from 0 °C to 50 °C and...
Index: SEE-12378
Index: SEE-12378
Grove - Base Shield for Arduino Nano
Shield for Arduino Nano is a board fully compatible with Seeeduino Nano. It has 8 connectors, so it is possible to connect many devices, sensors, Grove displays using 4-pin...
Index: SEE-14994
Index: SEE-14994
Grove - DS1307 real-time clock I2C
Module from Grove features a real time clock DS1307, which voltage is supplied by a round CR1225 battery (not included) . It allows you to read the time in hours, minutes,...
Index: SEE-13332
Index: SEE-13332
Capacitive touch sensor based on the module TTP223-b is supplied with the voltage from 2 V to 5.5 V, the output is a digital signal.
Index: SEE-04431
Index: SEE-04431
Grove - module with MOSFET transistor
It allows for turning on and off devices that require power from 5V to 15V with a digital signal. Switching frequency up to 5 MHz. It has two mounting holes, two ARK...
Index: SEE-11339
Index: SEE-11339
Grove RGB LED Stick - LED RGB 10 x WS2813 Mini 3535
The panel consists of 10 individually addressed RGB LEDs WS2813 Mini-3535 with built-in control unit. LEDs located on the panel are controlled with just one signal pin.
Index: SEE-13662
Index: SEE-13662
Connector Grove to GROVE - 5pcs
The connector Grove to Grove is an extension module of the standard Grove connector. It has a female Grove port (socket) on both ends. It is used to extend the...
Index: MSS-18101
Index: MSS-18101
Grove - push button with backlight - blue
Module from the Grove is equipped with a button with a blue LED. Powered with the v oltage from 3.3 V to 5 V. It has the Grove connector that allows for the direct...
Index: SEE-13660
Index: SEE-13660
Grove - Shield for Seeeduino XIAO - Seeedstudio 103020312
Overlay for Seeeduino Xiao , extending the capabilities of pins I / 0. Provides compatibility of the module with Grove series sensors. It has 8 built-in Grove connectors,...
Index: SEE-17041
Index: SEE-17041
Module from the Grove series, based on the LM386 system and electret microphone. It can be powered with any voltage from 4 V to 12 V. The output is an analog signal. The sensor...
Index: SEE-11350
Index: SEE-11350
Grove - push button with backlight - red
Module from the Grove is equipped with a button with a yellow led. It is powered with the voltage from 3.3 V to 5 V. It has the Grove connector that allows for the direct...
Index: SEE-13661
Index: SEE-13661
Grove - Pi+ StarterKit for Raspberry Pi 4B/3B+/3B/2B
Starter set introducing to the world, IoT (Internet of Things) for the Raspberry Pi. The set includes i.a.: sensors of light, sound, temperature, relay, display and many...
Index: SEE-04447
Index: SEE-04447