Description
Minicomputer with Windows 10 installed! Equipped with a processorIntel Cherry Trail Z8350 Quad Core 1.8 GHz. In addition, it has2 GB of RAMand32 GB of built-in memory EMMC,wi-fi and Bluetooth 4.0, 2x USB 2.0, 1x USB 3.0, microSD slot, Ethernet port. In addition, Panda feature microcontrollerATmega32u4 known from Arduino Leonardo, which controls 20 GPIOs. This combination allows the direct programming of the embedded Leonardo of Windows 10 via the serial interface.
|
LattePanda has installed operating system Windows 10! |
What it takes to run LattePanda?
- MicroUSB power supply - with minimum load current of 2 A, for example:power supplies designed for Raspberry Pi.
- HDMI cable- to connect the device to the monitor.
- Mouse and keyboard - to control and input data into the device.
First run
Starting LattePanda is very easy, to enjoy the OS from desktop Windows 10 you have to:
- Connect the power adapter with microUSB connector with performance above 2 A, for example,the power supply for the Raspberry Pi.
- The led located under the device should illuminate red.
- Then just press and hold the Power button (the first one next to the Ethernet slot) for approx. 1 sec.
- Minicomputer will start, showing on the screen the logo LattePanda.
- Now, you just have to configure Windows 10 in the same way as, for example, after buying a new laptop.
LattePanda also has connectors formodules and sensors from the DFRobot Gravity.
Operating system
Disk of LattePanda is embedded memory EMMC. Windows 10's operating system is already installed by the manufacturer. Just run minicomputer and configure Windows to your likings.
The picture and sound
LattePanda has aHDMI port through which you can send picture and sound.
In our offer, you will find also:display IPS 7"anda touchpadfor LattePanda.
Power
As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage have values of 5 V and the minimum current must be not less than 2.0 A. This criteria are met by the power supplies for the Raspberry Pi 3B and 2B minicomputer.
Minicomputer LattePanda - top view.
Communication
LattePanda has basic communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors for audio and video, the user has at his or her disposal:
- three connectors: USB 2x USB 2.0 + 1x USB 3.0 to which you can connect, for example, a mouse, keyboard or USB flash drive. If you find that the slots are too short, you can increase their number usingan external USB HUB.
- Ethernet slot, that is the ability to directly connect to the LOCAL network
- the wi-fi moduleallows communication with wireless network 802.11 b g n
- Bluetooth 4.0- allows data transmission through the interface
- GPIO- outputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers of engines. 20 pins are navigated through the coprocessor Atmega32u4 known from boardArduino Leonardo.
Distribution of connectors for minicomputer LattePanda.
Compatible with Arduino
Minicomputer has additional microcontroller Atmega32u4 - known from boardArduino Leonardo. This system operates 20 digital I/O and interfaces designed to communicate with modules and sensors like: UART, I2C, SPI. In addition, the manufacturer installed several connectors formodules of the series DFRobot Gravity.
In our offer you will finda special starter kitwith sensors and modules for LattePanda
Specifications and comparison with Rasberry Pi 3
| Basic information | |||
 |
 |
 |
|
| Model | LattePanda 2GB | LattePanda 4GB | Raspberry Pi 3 B |
| Technical specification of | |||
| Processor chipset |
Intel Cherry Trail Z8350 |
Intel Cherry Trail Z8350 |
Broadcom BCM2837 64-bit |
| The number of cores | 4 (Quad Core) | 4 (Quad Core) |
4 (Quad-Core) ARM Cortex |
|
Operating systems |
Linux Raspbian Windows 10 flight |
||
| Clock frequency | 1.8 GHz | 1.8 GHz | 1.2 GHz |
| RAM | 2 GB DDR3L | 4 GB DDR3L |
1 GB LPDDR2 |
| Memory |
32GB EMMC (built-in) |
64 GB EMMC (built-in) |
microSD memory card |
| Coprocessor |
Atmega32u4 in accordance with supports GPIO |
Atmega32u4 in accordance with Arduino Leonardo supports GPIO |
- |
| Graphics |
200 MHz (500 MHz) 1920x1080px |
200 MHz (500 MHz) 1920x1080px |
VideoCore IV 3D graphics core |
| GPIO slot |
|
|
Connector 2x20 pin male |
| The number of GPIO |
20 - Atmega32u4 2 - Intel |
20 - Atmega32u4 2 - Intel |
40 - Broadcom |
| Power |
5.0 V / 2.0 A via microUSB |
5.0 V / 2.0 A via microUSB |
A 5.1 V / 2.5 A via microUSB |
| Tile sizes | 88 x 70 mm | 88 x 70 mm | 85 x 56 mm |
| Interfaces | |||
| USB interface |
2x USB 2.0 - type A 1x USB 3.0 - type A |
2x USB 2.0 - type A 1x USB 3.0 - type A |
4x USB 2.0 - type A |
| Network interface |
Ethernet port 10/100 Mbps |
Ethernet port 10/100 Mbps |
Ethernet port 10/100 Mbps |
| The Wi-Fi Interface |
802.11 b/g/n 150 Mbps |
02.11 b/g/n 150 Mbps | 802.11 b/g/n 150 Mbps |
| Bluetooth | Low Energy, BLE 4.0 | Low Energy, BLE 4.0 | Low Energy, BLE 4.1 |
| Camera | - | - | the CSI slot |
|
Touch display |
special slot | special slot | slot for DSI |
| Video |
HDMI HD 1080p 30 fps |
HDMI HD 1080px 30 fps |
HDMI HD 1080px / 30 fps |
| Audio | HDMI + audio Jack | HDMI + audio Jack | HDMI + audio Jack |
| Communication | UART, SPI, I2C, GPIO | UART, SPI, I2C, GPIO | UART, SPI, I2C, GPIO |
Included
- Minicomputer LattePanda
- External wi-fi antenna
Useful links |
