Strip with QTRX-MD-05RC reflector sensors - 5-channel - digital - Pololu 4345

Index: PLL-13047 EAN: 5904422347956

Compact strap with five reflective sensors with the size of 37 x 20 mm. It has digital outputs, is powered with the voltage from 2.9 V to 5.5 V and allows for the adjustment of brightness regardless of the supply voltage. It detects the objects at a distance of about 40 mm.

Strip with QTRX-MD-05RC reflector sensors - 5-channel - digital - Pololu 4345
€10.50
€8.54 tax excl.
Waiting time: 4-6 weeks
Only on request
PayPal payment
QTRX-MD rebound sensor strip:
Manufacturer: Pololu
Compatibility: Arduino

Description

The strap is used in robots like line follower as sensors detecting the track as a black line on a white background. The module consists of five reflective sensors that contain the transmitting IR LED and receiver in the form of phototransistor. Output are the digital signals that can be read using any microcontroller, including Arduino. Sensor QTRX features with a smaller consumption of current than QTR.

 

Service

Strap QTRX-MD-05RC has digital outputs. Reading the measurement data is carried out by charging the capacitor (indicating the high status), and measuring the time of its discharge through phototransistor. This option has the following advantages:

  • It does not require an analog-to-digital converter
  • It gives the opportunity for parallel reading of the value from the six sensors
 

A typical sequence of the reading of sensor values:

  1. Turning on IR LEDs (optional)
  2. Setting the I/O pins of the microcontroller as output and the creation of the high status
  3. Wait a few micro seconds - charging the 2.2 nF capacitor 
  4. Setting the I/O pins as input (high impedance status)
  5. Measuring the discharge time of the capacitor by waiting until the I/O lines go to low status
  6. Disabling the IR LEDs (optional)
 
With a high intensity of the reflected signal, the measured time will be oscilating within a few microseconds. A small amount of reflected light will be discharging the capacitor within a few milliseconds. The exact time depends on characteristics of the pins of the microcontroller.
 

The product is compatible with Arduino

For users of modules Arduino manufacturer has prepared a special library that simplifies maintenance of the sensor library of Arduino.

The optimal distance of the sensors from the surface, is 10 mm, the maximum, at which the sensor operates, is 40 mm. To picture the situation, we present the oscilograms showing the detection of black line on a white background at different distances from the surface.

Digital signal (yellow) after the detection of black lines on a white base in the immediate area and clock frequency of the microcontroller (blue) - with the left and then the right side.

 

Scheme

Each of phototransistors has an external pulling-up capacitor and the auxiliary circuit providing the read of data from the sensors by measuring the time of discharge.

 

Current of each LED was set to 3.5 mA, the maximum current consumption of the module is approximately 14 mA.

Diagram of the module QTRX-MD-05RC.

The control of emitter

Matrixes have reflective sensors that can maintain a constant current through your IR transmitters, maintaining a constant brightness of the emitter, regardless of the supply voltage. Emitters can be controlled with the CTRL pins on the board, control is depending on the size and density of the matrix:

  • Modules with five or more sensors of high density (HD) have two pins controlling the emitter: ODD CTRL and EVEN CTRL. By default, they are connected with resistor of 1 kΩ, by default, turning on all transmitters and allows for their control using a signal on each of the pins. Pins ODD CTRL and EVEN CTRL can be used separately for independent control of transmitters with odd numbers and even numbers.
  • Modules with three or more sensors with medium density (MD) also have two pins controlling the emitter, only CTRL ODD pin will be able to manage in this version.
  • Modules with four or less sensors have a single CTRL pin that controls all the emitters.

Specification:

  • Number of sensors: 5
  • Supply voltage: from 2.9 V to 5.5 V
  • Current consumption: 14 mA
  • Current consumption of one LED: 3.5 mA
  • Outputs: digital
  • The optimal measurement distance: 10 mm
  • The maximum distance of measurements: 40 mm
  • Light wavelength: 940 nm
  • Sensor type: QTR
  • Distance between sensors: 8 mm
  • Dimensions 37 x 20 x 3 mm
  • Weight: 1.9 g

 


Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: