Product description: Arduino Nano 33 BLE Sense Rev2 - ABX00069
The task of the Arduino Nano series modules is to extend the possibilities of small boards in order to use them in any project. Arduino Nano 33 BLE Sense Rev2 is equipped with an energy-saving and efficient nRF52480 microcontroller that can work with a clock speed of up to 64 MHz . On its board there is space for 1 MB of Flash memory and 256 kB of RAM. Thanks to the use of this unit, the Nano 33 BLE Sense Rev2 board is the most energy-efficient representative of the Nano family. In addition, the board is equipped with a number of sensors, giving a lot of possibilities. It supports Bluetooth 5.0 Low Energy communication.
|
The offered board has leads for self-assembly. We also offer a version with connectors . |
Arduino Nano 33 BLE Sense Rev2.
Arduino Nano 33 BLE Sense Rev2 managing Bluetooth communication in the 5.0 LE standard.
Capabilities of Arduino Nano 33 BLE Sense Rev2
Arduino Nano 33 BLE Sense is equipped with the U-blox NINA B306 module that manages Bluetooth communication in the 5.0 LE standard . On board Nano there are two IMU (Inertial Measurement Unit) - 6-axis BMI270 and 3-axis BMM150 communicating via the I2C bus, which includes a 3-axis gyroscope, accelerometer and magnetometer. In addition, the small size of the board is equipped with a temperature and pressure sensor LPS22HB , a humidity sensor HS3003, a sensor of light intensity, colors and gestures ADPS-9960 . There was also room for the MP34DT05 digital microphone . In addition, the ATECC608A cryptographic chip was also on board.
Module power supply
Arduino Nano 33 BLE Sense only works with 3.3 V by default . In the place of the 5 V pin on the standard Nano board (between the RST and A7 pins), there is a jumper that can be shorted to USB power. To power the devices with 5 V, solder the jumper and power the Nano via USB . If the jumper is soldered and the power is taken from the VIN pin, no voltage will be obtained. This is a protection designed to protect the Arduino Nano 33 BLE Sense.
Attention!
Arduino Nano 33 BLE Sense can only work with 3.3 V by default. Do not power it directly with 5 V.
Arduino Nano 33 BLE Sense pins. Visible jumper for 5 V power supply via USB.
Kit contents.
Arduino Nano 33 BLE Sense board specification
- Supply voltage: 3.3V
- Microcontroller: nRF 52840
- Clock: 64MHz
- Flash memory: 1MB
- RAM memory 256 kB
- Digital pins: 14
- PWM pins: 6
- Analog pins: 8
- microUSB socket
- Interfaces: GPIO, SPI, I2C, USART, PWM
- Converters: ADC, DAC
- Dimensions: 45x18mm
Kit contents
- Arduino Nano 33 BLE Sense Rev2 - ABX00069
- A set of goldpin connectors
Leads
| Pin | Designation | Type | Description |
|---|---|---|---|
| 1 | D13 | Digital | GPIOs |
| 2 | +3V3 | Power output | Powering external devices |
| 3 | AREF | Analog | Reference pin, can be used as GPIO |
| 4 | A0 / DAC0 | Analog | ADC input / DAC output, can be used as GPIO |
| 5 | A1 | Analog | ADC input, can be used as GPIO |
| 6 | A2 | Analog | ADC input, can be used as GPIO |
| 7 | A3 | Analog | ADC input, can be used as GPIO |
| 8 | A4 / SDA | Analog | ADC input, I2C SDA, can be used as GPIO* |
| 9 | A5 / SCL | Analog | ADC input, I2C SCL can be used as GPIO* |
| 10 | A6 | Analog | ADC input, can be used as GPIO |
| 11 | A7 | Analog | ADC input, can be used as GPIO |
| 12 | USB | Power I/O | Normally not connected. Can be shorted to USB power |
| 13 | RST | digital input | Active reset |
| 14 | GND | Power | Mass |
| 15 | VIN | Power | Power |
| 16 | TX | Digital | USART TX , can be used as GPIO |
| 17 | RX | Digital | USART RX , can be used as GPIO |
| 18 | RST | Digital | Active reset |
| 19 | GND | Power | Mass |
| twenty | D2 | Digital | GPIOs |
| 21 | D3/PWM | Digital | GPIO, can be used like GPIO |
| 22 | D4 | Digital | GPIOs |
| 23 | D5/PWM | Digital | GPIO, can be used like GPIO |
| 24 | D6 / PWM | Digital | GPIO, can be used like GPIO |
| 25 | D7 | Digital | GPIOs |
| 26 | D8 | Digital | GPIOs |
| 27 | D9/PWM | Digital | GPIO, can be used like GPIO |
| 28 | D10 / PWM | Digital | GPIO, can be used like GPIO |
| 29 | D11 / MOSI | Digital | SPI MOSI , can be used like GPIO |
| thirty | D12 / MISO | Digital | SPI MISO , can be used like GPIO |
(*) Unlike the standard Arduino Nano, pins A4 and A5 have default pull-ups. pull-up and are used as an I2C bus, so it is not recommended to use them as analog inputs.
