Arduino sensors - Strona 3
Set of 13 modules with cables for Arduino - Waveshare 9467
Set of 13 popular modules compatible with Arduino plates. In the set are i.a.: sensors of flames, color, soil moisture, rotation, sound, liquid level and many others. The...Grove - sensor / probe for measuring soil moisture v1.4 - analog
The sensor allows you to determine the moisture level of the soil. It is supplied with the voltage from 3.3 V to 5 V. The output has analog voltage, which increases its value...Grove - a set of 5 female-female 4-pin - 2mm/20cm cables with a latch
A set of five 4-pin Grove wires. They are used to connect sensors with Grove Base Shield v2. Wire length is 20 cm. Version with a latch.Grove - a set of 5 female-female 4-pin - 2mm/20cm cables without latch
A set of five 4-pin cables Grove, raster 2 mm. They are used to connect Grove sensors with Base Shield Board. Cable length is 20cm. Version without a latch.Grove - a set of 5 female-female 4-pin - 2mm/5cm cables with a latch
A set of five 4-pin wires Grove. They are used to connect Grove sensors with Base Shield Board v2. Wire length is 5 cm. Version with lock.Grove - 4-pin screw connection
Module from the Grove series with a 4-pin screw connection of 3.5 mm. It is designed to connect the cables with diameter from 0.2 mm to 0.8 mm for the microcontroller. It has...Grove - 10kΩ linear rotary potentiometer - top connector
Potentiometer 10 kOhm with linear rotary. It as a 300° range of rotation. It h as a 4-pin Grove connector on the side of the handle.Grove - Buzzer - module with active buzzer
Active buzzer module from Grove. It e mits a uniform tone after taking a high position. When using PWM, it can generate different sounds and effects. The power voltage from 4...Grove - IR receiver 38kHz 940nm
IR receiver from Grove , operating at a frequency of 38 kHz with a supply voltage from 3.3 V to 5.0 V. Maximum sensitivity is observed for the wave length of 940 nm.Grove - set of 5 female-female 4-pin - 2mm/30cm with latch
A set of five 4-pin Grove wires. They are used to connect sensors with Grove Base Shield v2. Cable length is 30 cm. Version with a latch.Grove - SW-420 vibration sensor
Module with high sensitivity vibration sensor from Grove series. When the sensor is at rest, the output of the output transmitted is at a constant high signal (high) and the...Grove - 10kΩ rotary potentiometer linear lower connector
Potentiometer 10 kOhm with linear rotary. It has a 300° range of rotation. It has a 4-pin Grove connector on the other side of the handle. The kit includes a cable adapted...DFRobot Gravity: digital I2C multiplexer - 8-channel
Module with multiplexer that allows you to connect 8 different digital I2C buses to one interface, for each, there are separate pins SDA (bus of data line) and SCL (clock line...Gravity - DHT22 digital temperature and humidity sensor - DFRobot SEN0137
DFrobot's DHT22 digital humidity and temperature sensor module provides precise measurements and has a short response time combined with high reliability and resistance to...Grove - Button - module with a button
The control module from a Grove series. It has a built-in tact-switch system and pull-down resistor. It communicates with the microcontroller through a digital signal.Grove - module with MOSFET transistor
It allows for turning on and off devices that require power from 5V to 15V with a digital signal. Switching frequency up to 5 MHz. It has two mounting holes, two ARK...Grove - air purity sensor MP503 v1.3
Air purity sensor from Groveseries. It is used for detecting slightly toxic gases such as carbon monoxide, alcohol, acetone, thinner, formaldehyde and other.DFRobot KIT0011 - set of 27 modules with cables for Arduino
A set of 27 popular modules compatible with Arduino boards. In the set are i.a.: distance, light, touch, rotation, vibration, gas sensor, and a module with LED, relay and more....Grove - a set of 5 female-female 4-pin - 2mm/20cm I2C splitters
A set of five 4-pin wires Grove. With them you can connect two I2C Grove modules to one connector of the I2C bus, for example on the Base Shield v2 board. Cables are compatible...Temperature and humidity sensor - Sensirion SHT40 - STEMMA AT/Qwiic - Adafruit 4885
Temperature and humidity sensor from Adafruit. Equipped with Sensirion SHT40 chip and STEMMA QT / Qwiic connectors, which facilitate the connection of the sensor with...