Grove modules - Strona 2
Grove - Buzzer - module with active buzzer
Active buzzer module from Grove. It e mits a uniform tone after taking a high position. When using PWM, it can generate different sounds and effects. The power voltage from 4...Grove - ProtoShield - prototype board
Prototype board Grove with a soldered socket. It allows for an easy access to four lines of a standard Grove-S0, S1, VCC and GND series connection cable. The layout of the...Grove - IR receiver 38kHz 940nm
IR receiver from Grove , operating at a frequency of 38 kHz with a supply voltage from 3.3 V to 5.0 V. Maximum sensitivity is observed for the wave length of 940 nm.Grove - a speaker with a digital interface
Speaker module Grove is a device controlled by the PWM signal. It c an work as a simple buzzer or audio player. The volume is adjustable with the built in potentiometer. The...- Reduced price
- Promotion
Grove - set of 5 female-female 4-pin - 2mm/30cm with latch
A set of five 4-pin Grove wires. They are used to connect sensors with Grove Base Shield v2. Cable length is 30 cm. Version with a latch.Grove - capacitive humidity sensor - corrosion resistant
The device is used to measure the soil moisture by the capacitive detection. It has a built in voltage regulator which provides an operating voltage in the range from 3.3 V to...Grove - Shield for micro:bit v2.0
Grove Shield v2.0 overlay for micro:bit features 4 4-pin connectors for easy connection of Grove series sensors to the minicomputer.- Reduced price
- Promotion
Grove - LoRa-E5 STM32WLE5JC - EU868/US915 - LoRaWAN radio module - Seeedstudio 113020091
LoRa-E5 radio module with Grove connector, manufactured by Seeedstudio. It features an STM32WLE5JC chip with a low-power 32-bit ARM Cortex M4 processor with a clock...Grove Shield for Raspberry Pi Pico - Seeedstudio 103100142
Grove frontend for Raspberry Pi Pico module . Converts Pico GPIO connectors to Grove type connectors such as I2C, UART and digital and analog ports. It allows you to...Grove - 10kΩ rotary potentiometer linear lower connector
Potentiometer 10 kOhm with linear rotary. It has a 300° range of rotation. It has a 4-pin Grove connector on the other side of the handle. The kit includes a cable adapted...Grove - temperature and humidity sensor DHT11 - Seeedstudio 101020011
The sensor of temperature and humidity DHT11 from the Grove series. The output is a digital signal. The temperature measurement range is from 0 °C to 50 °C and...Grove - Cable Pigtail - 4-pin connection cable - 10cm - Adafruit 5244
Connection cable from Adafruit. On one side it has four isolated wires (each in a different color), and on the other side it has a connector compatible with the Grove...Grove - DS1307 real-time clock I2C
Module from Grove features a real time clock DS1307, which voltage is supplied by a round CR1225 battery (not included) . It allows you to read the time in hours, minutes,...Grove RGB LED Stick - LED RGB 10 x WS2813 Mini 3535
The panel consists of 10 individually addressed RGB LEDs WS2813 Mini-3535 with built-in control unit. LEDs located on the panel are controlled with just one signal pin.Grove - GSR sensor - electrical resistance of the skin
Module from the Grove series equipped with GSR sensor using the galvanic-skin reaction. It is powered with the voltage of 3.3 V or 5V. The s ensors of this type are used in...Grove - push button with backlight - blue
Module from the Grove is equipped with a button with a blue LED. Powered with the v oltage from 3.3 V to 5 V. It has the Grove connector that allows for the direct...Grove - Pi+ StarterKit for Raspberry Pi 4B/3B+/3B/2B
Starter set introducing to the world, IoT (Internet of Things) for the Raspberry Pi. The set includes i.a.: sensors of light, sound, temperature, relay, display and many...Grove - push button with backlight - red
Module from the Grove is equipped with a button with a yellow led. It is powered with the voltage from 3.3 V to 5 V. It has the Grove connector that allows for the direct...Grove - Base Shield for Arduino Nano
Shield for Arduino Nano is a board fully compatible with Seeeduino Nano. It has 8 connectors, so it is possible to connect many devices, sensors, Grove displays using 4-pin...Grove - analog NTC temperature sensor
Analog sensor is compatible with Arduino and Raspberry Pi. It is powered with the voltage from 3.3 V to 5 V. It can measure temperature in the range from -40 °C to 125 °C with...See also
- Piezoelectric sensors
- RPM sensors
- Oxygen sensors
- Tilt sensors
- Accelerometers
- Inductive sensors
- Hall effect sensors
- Led motion detectors
- Optical sensors
- Twilight sensors
- Resistance sensors
- Door sensors
- Alarm sensors
- 9DoF IMU sensors
- Pressure sensors
- Air quality sensors
- Sound sensors
- Gesture sensors
- Gas sensors
- Limit switches
- Sensors of light and color
- Magnetic sensors
- Medical sensors
- Pressure sensors
- Sensors odbiciowe
- Distance sensors
- Inductive contactless sensors
- Weather sensors
- Liquid level sensors
- Current sensors
- Flow sensors
- Motion sensors
- Temperature sensors
- PT100 temperature probes
- Humidity sensors
- Fingerprint readers
- Encoders
- Photoresistors
- Phototransistors
- IR receivers
- Magnetometers
- Gyros
- Sensor sets
- Gravity modules