- Reduced price
- Promotion
- On sale!
- Promotion
ELECTRONICS - Strona 39
Loading...
Step-Down Voltage Regulator - adjustable 3,3V - 25V 5A - DFRobot DFR0205
Inverter module for converting input voltage from 3.6 V to 25 V, to output voltage from 3.3 V to 25 V. The current capacity for 5 V is 5 A. The input voltage must be higher...
Index: DFR-15090
Index: DFR-15090
Grove - MMA7660FC 3-axis digital accelerometer I2C
Module with 3-axis accelerometer based on MMA7660FC chip with digital I2C output and Grove connector. The MEMS sensor has a low power consumption and low profile. The module...
Index: SEE-15444
Index: SEE-15444
- Reduced price
- Promotion
Cytron MDD3A - dual-channel 16V / 3A motor controller
The Cytron MDD3A motor controller has the ability to control 2 DC motors or 1 stepper motor. Continuous current per channel is 3 A (momentary 5 A). Supply voltage is from 4 V...
Index: CTN-15819
Index: CTN-15819
Peltier's cell TES1-12710 15,8V/10,5A
Peltier cell supplied with 15.8V . Current consumption is 10.5 A. The dimensions of the board are equal to 40 x 40 x 3.3 mm . It is used e.g. in portable fridges or...
Index: DNG-16371
Index: DNG-16371
Logic system CD4093BE 4xNAND with Schmitt trigger - 5pcs
Logic system with four NAND gates, with Schmitt's derailleur gears at the output, preventing the system from waking up. The voltage of the system is from 3 V to 18 V. The...
Index: UCC-17147
Index: UCC-17147
Electromagnet holding 12V 3W 15kgf
Powered by 12 V , a holding electromagnet that holds a mass of 15 kg under standard acceleration due to gravity (9.8 m/s 2 ). Current consumption during operation is...
Index: DNG-17570
Index: DNG-17570
Pulling electromagnet 12V 0,6kg
Electromagnet, which after giving a voltage signal of 12 V , allows for linear motion - pulling. The range of the device's pin is 10 mm and its maximum load capacity is 0.6...
Index: DNG-17758
Index: DNG-17758
Female socket 2x3 raster 2mm straight - 5pcs
A double-row female pin socket, which has a 2 x 3 distribution and a 2 mm raster. The module is black. It has a simple connector for THT threaded assembly. The length of...
Index: TME-18241
Index: TME-18241
LCD display 4x20 characters blue - justPi
Alphanumeric LCD display by justPi. It presents values in four lines, 20 characters each . It is powered by 5V. It is characterized by extremely simple operation, high...
Index: JUS-19734
Index: JUS-19734
LED 5mm 12V with resistor and wire - white - 5pcs.
5 mm white LED with an attached resistor and a cable approx. 20 cm long, powered with 12 V. The maximum current consumption by the diode is 22 mA . The LED lighting angle...
Index: DNG-21936
Index: DNG-21936
Inductance: 10 μH. Maximum current: 160 mA. Resistance: 2.5 Ω. Dimensions: 3 x 7 mm. Price for 10 pieces.
Index: PAS-00438
Index: PAS-00438
Phototransistor LIRT3B-940 3mm 940nm
Phototransistor in the case of 3 mm. Maximum sensitivity for the wave with the length of 940 nm. Darkened lens.
Index: UCC-01227
Index: UCC-01227
Radiator RAD07 15x14,5x6mm - 5 psc.
Heat sink with the size of 15 x 14.5 x 6 mm. Compatible with the Raspberry Pi minicomputer.
Index: ETN-01497
Index: ETN-01497
Socket DC 2,5/5,5 for the prototype contact plate
Connector suitable for standard prototypes of the breadboard with a pitch of 2.54 mm. the module allows to connect the power supply with the plug of 2.5/5.5 mm.
Index: MOD-01610
Index: MOD-01610
Extension cord for servos 15cm twisted
Extension cable with the length of 15 cm ended with the standard plug for the servos. It has twisted cables.
Index: KAB-01718
Index: KAB-01718
Temperature sensor TMP36GT9Z - analog THT
Analog thermometer, in which the output voltage is proportional to the measured temperature from the range: -40 °C to +120 °C. It is powered with the voltage from 2.7 to 5.5 V.
Index: SES-02558
Index: SES-02558
Index: KDX-06004
MAX31856 Breakout - Universal Thermocouple Amplifier - Adafruit 3263
Module with thermocouple amplifier MAX31856 communicating via the 4-pin SPI interface. Works with thermocouples of type K, J, N, R, S, T, E and B. Works with a supply voltage...
Index: ADA-07682
Index: ADA-07682
Cable gland hermetic IP68 - PG9 thread - black - 5 pcs.
Sealed cable gland with the thread of 15.2 mm. Prevents the cable passing through the body wall from rubbing. Designed for wire diameters from 3 mm to 6.5 mm. Items are sold...
Index: KAB-09461
Index: KAB-09461
The electric 5-pin cube that allows to connect the wires with the cross-sections from 0.75 to 2.5 mm.
Index: LEC-09986
Index: LEC-09986
LCD resistive touch screen TFT 4 480x320px SPI for Arduino - Waveshare 13587
Waveshare, resistive 4" touch screen for Arduino with 480 x 320 px resolution . There is also microSD card slot on the board. Works with Arduino and Nucleo via SPI interface....
Index: WSR-10757
Index: WSR-10757
Module with red LED, fitted with Grove connectors is ideal for working with Arduino. The LED turns on, when the signal pin goes into high state. In addition, on the board...
Index: SEE-11346
Index: SEE-11346
Grove - precipitation / water sensor
The Grove sensor used to detect the presence of water or its quantity. It is powered with the voltage of 5 V. It can be used to detect the presence, level or absence of water.
Index: SEE-11363
Index: SEE-11363
Filament Spectrum Smart ABS 1,75mm 1kg - Deep Black
Filament made of Smart ABS, used as a cartridge for 3D printers. The diameter is 1.75 mm. The set includes 1kg of filament in Deep Black color. It requires a heatbed.
Index: SPC-11447
Index: SPC-11447