• EOL

ATWINC1500 - WiFi SPI/UART + U.FL connector - Adafruit 3060

Index: ADA-05970 EAN: 5904422348748

Wi-fi module from Atmel operating in 802.11 bgn standard. The device works with voltage from 3.3 V to 5.5 V it communicates via interface SPI. It has support for SSL, WEP, WPA, WPA2 and AP mode which allows you to create ad-hoc network. The module also works with TLS 1.2 safety with firmware 19.4.4. On the board is a connector u.FL for connecting external antenna wi-fi.

ATWINC1500 - WiFi SPI/UART + U.FL connector - Adafruit 3060
€33.90
€27.56 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Adafruit
Compatibility: Arduino

Attention!

The product has been discontinued. Check other products in category.

Description

Wi-fi module from Atmel operating in 802.11 bgn standard. The device works with voltage from 3.3 V to 5.5 V it communicates via interface SPI. It has support for SSL, WEP, WPA, WPA2 and AP mode which allows you to create ad-hoc network. The module also works with TLS 1.2 safety with firmware 19.4.4. On the board is a connector u.FL for connecting external antenna wi-fi.

Key features

  • Module from ATmel ATWINC1500 (documentation) is working in standard WiFi 802.11 bgn
  • It has support for AP mode (Access Point) which allows you to create ad-hoc network
  • It works with a voltage of 3.3 V and 5.0 V
  • It communicates
  • It supports SSL, WEP, WPA, WPA2, and TLS 1.2 security with firmware 19.4.4

 

 

The product is compatible with Arduino

On the Adafruit website, you can findthe user manualalong witha libraryfor Arduino.

 

Connection

 

Pin Description
Vin DC supply voltage from 3.3 V to 5.5 V.
GND The ground of the system.
SCK Clock line of the SPI bus - is running with a voltage of 3.3 V and 5 V.
MISO The data line of the SPI bus - is running with a voltage of 3.3 V.
MOSI The data line of the SPI bus - is running with a voltage of 3.3 V and 5 V.
CS Chip Select - choice of an active device on the SPI bus by indicating the low status.
EN Indicating the high status from 3.3 V to 5 V, enabling the module.Indicating the low status, disabling the system. By default, pulled to GND with a resistor of 100 k (module is off)
IRQ The external interrupt.
Wake The signal to wake the module - it operates with a voltage of 3.3 V and 5 V. The unused pin in the Adafruit sample program.
RST Reset of the module, activated by the high status. By default, it is pulled to GND with a resistor of 100 k.
CFG The choice between the SPI interface (default) and UART interface.
RXD/TXD Communication pins of the UART interface.

Specification

  • Supply voltage: from 3.3 V to 5.5 V
  • The wi-fi module ATWINC1500
  • Support for AP mode
  • Support for securities WEP, WPA, WPA2 and SSL
  • Support for TLS 1.2 with firmware 19.4.4
  • Communication: SPI and UART interface
  • Connector u.FL to connect an external antenna wi-fi
  • Dimensions: 33 x 28 x 48 mm
  • Weight: approx. 5 g

 

UC - Microcontroller ATWINC1500
Package width 4 cm
Package height 4.4 cm
Package depth 0.1 cm
Package weight 0.007 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: