List of products by brand SparkFun - Strona 33
SparkFun Qwiic Alphanumeric Display - Pink - SparkFun COM-16919
Alphanumeric display based on the VK16K33 controller . It uses the I2C bus for communication. Built-in connectors allow the product to be connected to the Qwiic ecosystem...- EOL
SparkFun Pulsed Radar Breakout - A111 distance sensor module - for Raspberry Pi - SparkFun SEN-16826
A precision distance sensor from SparkFun in the form of a 60 GHz Pulsed Radar Breakout SparkFun with A111 chip. It provides a single-chip solution for pulsed coherent rad...- EOL
SparkFun Big Easy Driver Kit - stepper motor driver kit - SparkFun KIT-18339
A set consisting of a board compatible with Arduino - RedBoard Qwiic SparkFun DEV-15123 and a stepper motor driver - Big Easy Driver . RedBoard Qwiic has 14 digital inputs /...- EOL
SparkFun 2D Barcode Scanner Breakout - SparkFun SEN-18088
2D Barcode Scanner Breakout - A module produced by SparkFun and featuring the DE2120 barcode scanner from DYScan. Designed to read 20 different barcode symbologies or QR...- EOL
SparkFun Thing Plus - STM32 - SparkFun DEV-17712
The SparkFun Thing Plus board is equipped with an STM32F405 microcontroller with a 32-bit ARM Cortex-M4 core with FPU clock frequency up to 168 MHz. It has SPI Flash memory,...- EOL
SparkFun RED-V RedBoard - development board with SiFive RISC-V FE310 SoC - SparkFun DEV-15594
RED-V RedBoard development board from SparkFun. Equipped with a Freedom E310 SoC microcontroller with RISC-V (ISA) architecture, 32 MB QSPI Flash memory, NXP K22 ARM...- EOL
- EOL
SparkFun Qwiic Thermocouple Amplifier - MCP9600 - PCC - SparkFun SEN-16294
Module with a thermocouple amplifier equipped with the MCP9600 system. It uses the I2C communication interface via the Qwiic connector. It works with K-type thermocouples...- EOL
- EOL
Qwiic Shield for Thing Plus - hat - SparkFun DEV-16790
Cap that allows you to extend the functionality of the Thing Plus and Feather plates with additional Qwiic connectors . The product offers four additional connectors: two...- EOL
SparkFun Qwiic Shield - for Arduino Nano - SparkFun DEV-16789
SparkFun Qwiic Shield shield for Arduino Nano from SparkFun. The pin expander improves the Arduino prototyping process through four connectors of the Qwiic ecosystem. Two...- EOL
SparkFun Top pHAT - extension module with display - hat for Raspberry Pi - SparkFun DEV-16653
Shield for Raspberry Pi from SparkFun - SparkFun Top pHAT. Equipped with a TFT display with a diagonal of 2.4 '' and six RGB LEDs, two utility buttons and a joystick. It is...- EOL
SparkFun Auto pHAT - multifunctional expansion module for Raspberry Pi - SparkFun ROB-16328
Multifunctional extension module from SparkFun designed for use with Raspberry Pi. It is compatible with any version equipped with a GPIO in a 2x20 chip, as well as with...- EOL
SparkFun MicroMod Main Board - Single
SparkFun Edge Development Board - Apollo3 Blue equipped with 32-bit ARM Cortex-M4F microcontroller with 48 MHz and 96 MHz processor clocking with TurboSPOT. Has 1 MB Flash...- EOL
- EOL
SparkFun Qwiic Ultrasonic Distance Sensor - 2-400cm - HC-SR04 - SparkFun SEN-17777
Ultrasonic distance sensor from SparkFun. It works in the range from 2 cm to 400 cm , with an accuracy of 3 mm . The detection angle is 15 degrees . The sensor has Qwiic...- EOL
SparkFun Qwiic Starter Kit - for Raspberry Pi - SparkFun KIT-16841
The SparkFun Qwiic Starter Kit consists of the Sparkfun Qwiic pHAT v2.0 pin expander in the form of an overlay for the Raspberry Pi, which extends the possibilities of the...- EOL
SparkFun Qwiic Pro Kit - SparkFun KIT-15349
Qwiic Pro Kit development kit from SparkFun. It includes the RedBoard Turbo board, a module with a proximity sensor and a 3-axis accelerometer , connecting cables with a...- EOL
SparkFun RFID Qwiic Kit - SparkFun KIT-15209
SparkFun RFID Qwiic Kit with RFID Qwiic Reader and RFID ID-12LA module and I2C interface. The carrier frequency of the kit components is 125 kHz . The set can be used with...- EOL
SparkFun QwiicBus Kit - SparkFun KIT-17250
A set from SparkFun consisting of modules for building a communication system based on QwiicBus . It includes two QwiicBus EndPoint end modules , one QwiicBus MidPoint...- EOL
MyoWare 2.0 Link Shield - MyoWare 2.0 muscle sensors adapter for Arduino - SparkFun DEV-18425
A module that allows you to connect the EMG MyoWare 2.0 muscle sensors to the Arduino microcontroller board. The board is equipped with a 3.5 mm TRS jack connector , so you...- EOL
MyoWare 2.0 Muscle Sensor - SparkFun DEV-18977
EMG MyoWare 2.0 muscle sensor by Advancer Technologies. The board is equipped with three snap connectors to which you can connect other MyoWare 2.0 overlays to realize a...- EOL
MyoWare 2.0 LED Shield - SparkFun DEV-18387
The MyoWare 2.0 LED overlay is equipped with a 10-segment (2 x 5) blue display. The display in conjunction with the EMG MyoWare 2.0 muscle sensor can indicate their...- EOL
MyoWare 2.0 Power Shield - SparkFun DEV-18427
MyoWare 2.0 Power Shield is a power shield for modules from the MyoWare 2.0 series. It is equipped with a 3.7 V lithium-ion battery with a capacity of 40 mAh , snap-on...- EOL