ELECTRONICS - Strona 28
Inveo - RFID-USB-DESK reader - Unique 125kHz
Inveo module for reading data from RFID devices in the Unique 125 kHz standard. The reader connects to the USB port. The system is seen as a virtual COM port. It has 3 LEDs and...Disk for optical encoders - 25mm
Disk of optical encoder is designed for installation in engines with a shaft with the size of 5 x 4 mm. The outer diameter is equal to 25 mm.OBD-II CAN-BUS Development Kit
OBD-II CAN-BUS Development Kit for Arduino, Raspberry, Beaglebone and other minicomputers, allowing to connect the computer with the vehicle's OBD-II interface and perform...MicroHDMI cable - HDMI 2.0 original for Raspberry Pi 4/5 - 2m - black
Officially licensed by the Raspberry Pi Foundation microHDMI cable to connect RPi 4 or RPi 5 minicomputer with monitor. 2 m long model in black .Electromagnet holding 12V 6W 55kgf
Holding electromagnet with a rated power of 6 W. Powered by 12 V. Current consumption is approximately 500 mA. The device maintains a mass of 55 kg under standard...Pulling electromagnet 12V 0,5kg
A device whose task is to perform linear motion - pulling, after giving a 12 V voltage signal. The electromagnet draws about 0.6 A current. The range of the pin is 5 mm....JustPi THT CF carbon resistor 1/4W 1,2kΩ - 30pcs.
The set consists of 30 resistors. The electronic elements are designed for THT through-hole mounting. Resistance is 1.2 kΩ and tolerance is 5%.AP63203 - step-down BabyBuck voltage regulator - 3,3V 2A - SparkFun COM-18357
Step-down converter , made by SparkFun. The AP63203 voltage regulator changes the input voltage from 3.8 V to 32 V to the output: 3,3 V . The current capacity of the...Quartz resonator 4MHz - HC49 - low - 10 pcs.
The quartz resonator in the small through hole case.Step-Down Voltage Regulator D24V6F5 - 5V 0,6A - Pololu 2107
Converter, type step down with an output voltage of 5 V. The maximum current up to 600 mA. Supply voltage ranges from 6 V to 42 V.Diode Power LED Star 1 W - white with heat sink
Diode Power LED Star 1W with a heat sink. Emits light in a cool white color, close to daylight.Memory card M1AA Goodram microSD 16GB 100MB/s UHS-I class 10 with adapter
Popular format of micro SD/SDHC card, which is used in smartphones, tablets, cameras. Product of class 10 with UHS-I interface from company Goodram. Speed of the read : up...D-SUB 25 socket for wire - 5pcs.
D-SUB 25 male connector for cable used for example as LPT parallel port connector.WiFi module ESP8266 Wemos NodeMCU V3 32Mb - 11 GPIO, ADC, PWM
Wi-fi module based on ESP8266. On Board 11 GPIO ports (each of which can handle PWM, I2C and 1-wire), built-in ADC and USB-UART converter. It has installed NodeMCU software...Push Button 6cm - yellow - flat
Large, flat button with an outer diameter of 6 cm with built-in LED illuminating the dome.RTC DS1307 + 32kb EEPROM 24C32 I2C - real-time clock with memory
Module with real time clock and backup battery. It allows you to read the time in hours, minutes, and seconds, date: month, day, year. It has 32 KB of EEPROM. The...Grove - MMA7660FC 3-axis digital accelerometer I2C
Module with 3-axis accelerometer based on MMA7660FC chip with digital I2C output and Grove connector. The MEMS sensor has a low power consumption and low profile. The module...- Reduced price
- SPECIAL OFFERS
MiniUSB B - A cable 2.0 Lanberg 0,3m - black
High-quality miniUSB 2.0 cable in black, from Lanberg. It is perfect for connection between a computer and a digital camera or MP3 player. It can also be used with devices with...Electromagnet holding 12V 1W 80mA 1kgf
Holding electromagnet, powered by 12 V. With standard acceleration due to gravity (9.82 m/s 2 ) it maintains a mass of 1 kg . Current consumption is approx. 80 mA, rated...Remote control - 433.92 MHz - 4-channel
A remote control enabling control of up to 4 devices operating at 433.92 MHz . Such a solution works well in case of having e.g. 4 gates, and each of them is controlled by...- Reduced price
- SPECIAL OFFERS
JustPi THT CF carbon resistor 1/4W 3,3kΩ - 30pcs.
The set consists of 30 resistors. The electronic elements are designed for THT through-hole mounting. Resistance is 3.3 kΩ and tolerance is 5%.
