Motor 2040 - quad motor controller 10V/0,5A - RP2040 - Pimoroni PIM618

Index: PIM-21934 EAN: 769894021651
The Motor 2040 is a standalone motor controller designed to control DC motors with encoders. The module is based on the Raspberry Pi RP2040 , so there is no need to use additional boards with a microcontroller. The controller is able to handle four DC motors with a supply voltage from 2.7 V to 10 V and a current consumption of 0.5 A. The board also has an addressable RGB Neopixel LED, status LEDs for each engine, Boot and Reset buttons, and a Qwiic / STEMMA QT connector. The motor 2040 is powered via the USB type C connector.
Motor 2040 - quad motor controller 10V/0,5A - RP2040 - Pimoroni PIM618
€33.90
€27.56 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: PiMoroni

Product description: Motor 2040 - 4-channel motor controller 10 V / 0.5 A - RP2040 - Pimoroni PIM618

The Motor 2040 is a standalone motor controller designed to control DC motors with encoders. The module is based on the Raspberry Pi RP2040 , so there is no need to use additional boards with a microcontroller. Two DRV8833 drivers built into the board are able to handle four DC motors with a supply voltage from 2.7 V to 10 V and a current consumption of 0.5 A. The board also has an addressable RGB Neopixel LED, status LEDs for each engine, Boot and Reset buttons, and a Qwiic / STEMMA QT connector. The motor 2040 is powered via the USB type C connector.

Motor 2040 driver board Motor 2040 motor driver with Raspberry RP2040 microcontroller.
Moro 2040 engine controller

Motor 2040 - 4-channel motor controller 10 V / 0.5 A - RP2040 - Pimoroni PIM618.

The main features of the Motor 2040 module

  • Based on the Raspberry Pi RP2040 microcontroller - ARM Cortex M0 + Dual Core 133 MHz with 264 KB of SRAM
  • 2MB QSPI Flash with XiP support
  • Two H-bridge drivers (DRV8833)
  • 4 JST-SH 6-pin connector for connecting motors
  • Wide range of motor and logic voltages supported (2.7V to 10V)
  • Built-in voltage regulator 3.3 V with input voltage up to 13.2 V (the maximum current efficiency of the regulator is 150 mA)
  • Measurement of voltage, current and error detection
  • Current limit 0.5 A per motor
  • Status LED for each engine
  • Addressable LED / Neopixel
  • Reset and Boot button
  • USB Type-C connector for programming and power (max. 3 A)
  • Qwiic / STEMMA QT connector for rapid prototyping
  • Fully assembled

Power Motor 2040

The Motor 2040 board can be powered via the USB type C connector from the computer or powerbank port or via the battery using the EXT PWR or VSYS pins. The module should only be powered from one source at a time. However, if the module is to be powered from two different sources at the same time, cut the jumper at the bottom of the board.

  • Cut EXT PWR to VSYS if motors are to be powered separately (up to 10V) from the board. The power supply of the board (up to 13.2 V) will have to be provided via the USB 5 V or VSYS port.
  • Cut the 5V USB to VSYS if the board is to be fully powered from a separate power source, without worrying about re-powering the computer. The board will not turn on when it is connected only via USB.
Sample power diagram Sample power diagram.
RP2040 microcontroller RP2040 microcontroller.

RP2040 microcontroller

The RP2040 is the first microcontroller from the Raspberry Pi Foundation. This system was first used in the Raspberry Pi Pico module and in modules from other manufacturers, including Arduino. It is a very efficient, dual-core microcontroller based on ARM Cortex M0 + core clocked at 133 MHz . It has a large amount of built-in SRAM memory, programmable I / O (PIO) and other popular communication interfaces. The microcontroller is closed in the QFN-56 housing.

Motor 2040 specification

  • Microcontroller: RP2040
  • Driver for motors: 2x DRV8833
  • Supply voltage for motors and logic: 2.7 V to 10 V
  • Current efficiency: 0.5 A (after the current limiting pads are short-circuited, it is possible to obtain 1.2 A of continuous current and up to 2 A of instantaneous current - it is associated with the loss of the current measurement)
  • LED: RGB Neopixel
  • Regulator: 3.3 V / 150 mA
  • Dimensions: 52 x 38 x 7.7 mm
  • Mounting holes: M2.5 / 2.7 mm
Motor 2040 Jumpers on the back of the Motor 2040 board.

Voltage to 2.7 V
Voltage from 10.0 V
Current 0.5 A
Channels 4
Package width 8 cm
Package height 12 cm
Package depth 1 cm
Package weight 0.001 kg

Be the first to ask a question about this product!

Product reviews

Motor 2040 - quad motor controller 10V/0,5A - RP2040 - Pimoroni PIM618

5/5

Average grade

1

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Zdjęcia użytkowników

Customers who bought this product also bought:

Products from the same category: