For over half a century of intensive development of the electronics industry, both in consumer electronics, computers, household appliances, as well as in medical or industrial production, various manufacturers have been introducing more and more new types of power connectors. And - as it usually happens in such cases - only selected ones entered common use. These designs have become worldwide standards, which are known to every practicing electronics engineer. In this category you will find a wide range of cables and adapters used for supplying power to electronic devices and modules both with 230 V mains voltage and low DC voltage from power supplies or inverters.
Przewody i przejściówki elektroniczne
electric socket adapter for car lighter - 12V/0,5A
Stabilized power supply unit with car socket. Mains supply: from 100 V to 240 V. Output voltage: 12 V DC. Output current: 500 mA.PL plug - universal white socket LX6087B
The power plug is equipped with a universal socket (European, British, American) and an E-type plug . The adapter allows you to use electrical devices that are equipped with...AC IEC double male / female socket with latch
Dual IEC male / female slot mounted in the case on the latch.Cable for IEC computer power supplies - Lanberg - 1.8m
Power supply cable 1.8 m long with a female connector.Extension cord for IEC computer cable - 1.5 m
Extension cable for power supplies with a length of 1.5 m with female and male connectors.Adapter socket 5.5/2.1mm - microUSB plug
Adapter that allows for connection of the cable with the tip 5,5 / 2,1 mm with slot with type of microUSB. It can be used as an adapter to power Arduino and Raspberry Pi.Molex power cord - 2x SATA - 15cm
The adapter allows for the separation of the MOLEX connector to two SATA connectors. Cable length is 15 cm.SATA Data III wire (6GB / s) M / M 50cm - red
Cable SATA III complete with connectors at both ends, allows to achieve data transfer at 6 Gbps. It allows you to connect a CD drive or hard disk to the motherboard of the...DC splitter 5.5/2.1mm - 5 plugs - 40cm
Splitter with one 5.5 / 2.1 mm female socket and five 5.5 / 2.1 mm male plugs. It can be used, for example, for supplying many LED strips from one power supply.Splitter 3 flat sockets AC 230V 2.5A - Vorel 72401 - white
Splitter with three power sockets without earthing, with maximum load 2.5 A . It has one plug for 230 V mains voltage socket.Power cord for 3-pin power supply - length 1.5 m
Power cable for power supply with 3-pin "clover" connector. The standard is used, for example, in laptops. Cable length is 1.5 m.TP-Link Splitter PoE - TL-POE10R - 1Gbit
PoE splitter is fully compatible with devices of PSE or power supply PoE with the standard IEEE 802.3af. The splitter has an adjustable output voltage in the range of 5, 9...Molex power cord for mini-Molex + Molex - 15cm
Power cable with Molex connectors, 5.08 mm pitch and mini-Molex, 2.54 mm pitch + Molex, 5.08 mm pitch. The cable length is 15 cm.Splitter 4 flat sockets AC 230V 2.5A - Vorel 72402 - white
Splitter with four power sockets without earthing, with maximum load 2.5 A . It has one plug for 230 V mains voltage socket.Molex power cable to 2x Molex - 15cm
The adapter allows you to split the MOLEX connector into two separate MOLEX connectors.SATA power cable - SATA - 50cm
Male-male SATA connectors cable allowing you to connect a hard disk or CD-ROM to the motherboard of the computer. Cable length is 50 cm. Suitable for connector of Banana Pi.Extension cord for IEC - Lanberg computer cable - 1.8m
Extension cable for power supplies with a length of 1.8 m with female and male connectors.Triple splitter for AC 230V mains socket - 2 flat, 1 round
Mains power splitter equipped with one plug for 230 V mains voltage, as well as two flat sockets and 1 standard socket with earthing.DC Splitter 5.5/2.1mm - 4 plugs
Splitter with one 5.5 / 2.1 mm female socket and four 5.5 / 2.1 mm male plugs. It can be used, for example, for supplying many LED strips from one power supply.Zobacz również
Plugs, sockets, connectors - diversity for a good cause
The main differences between the design of connectors, cables and power adapters stem from two main parameters: operating voltage and maximum current carrying capacity. In the case of mains connectors (in most countries of the world, the mains voltage is around 230 V AC), two main groups can be distinguished: two-pin connectors (designed for devices operating in the second class of insulation) and three-pin connectors (for devices of the first class, i.e. equipped with protective earth). All these connectors must provide sufficiently robust insulation (the primary protection in all cases) and carry currents of at least a few amperes (usually 10 A or more). In the case of DC connectors, acceptable voltages are usually quite low (usually of the order of a few tens of volts), while the maximum current depends on the purpose of the component and ranges from about 1 A to 10 or more amperes.
Mains power circuit components
In this category you will find various types of mains cables and adapters, as well as useful connectors in the most well-known standards. For supplying power to desktop computers, most monitors and many other devices (e.g. oscilloscopes or laboratory power supplies), we offer 1.5m long mains cables terminated with IEC plugs, as well as dedicated extension cables (1.8m). Smaller devices (e.g. small household appliances or consumer electronics) are often equipped with two-pin eight-pin sockets and we also have suitable mains cables for them. Power supplies for laptops usually use the so called "clovers" - you will also find such cables in this category. In addition to cables, we have also included built-in power sockets (e.g. AC IEC male socket with a snap-on socket - with a fuse and a switch) and triple and quadruple 230 V splitters.
Cables and adapters
However, the variety does not only concern the power supply. Also the data transfer interfaces inside computers and embedded systems require the use of specialised cables and adapters. That's why in this category we placed, among others, SATA cables with throughput up to 6 GB/s, dedicated SATA adapters (data transfer and power supply) for Banana Pi minicomputers, as well as USB 3.0 - SATA modules dedicated for Odroid modules. You will also find here tapes for ATA devices (optical drives and hard drives with parallel interface) used in older computers.