You have a brilliant idea for a hardware and software project and would like to implement it yourself, but you lack the right elements and tools? You are sure that you could improve the comfort of your everyday life in the world with it, and perhaps even improve someone's quality of life? With Raspberry Pi microcomputers you have a chance to realize your plan and create an advanced system to manage an intelligent building, a weather station or a robot following your commands. It is a device with great constructional capabilities. It is perfect for programming and electronics. It can introduce you to the fascinating world of robotics, as well as surprise you with its potential, when you have quite a lot of experience. No matter what your plan is, you should have prototyping accessories to make your project more successful. Among the products available are contact plates with wires. These are the ones that allow you to give up the soldering iron, which means you have even more design possibilities. Our offer also includes starter kits, which will make it much easier for you to enter the extraordinary world of Raspberry Pi.
- New
- New
- On sale!
- Promotion
- On sale!
- Promotion
- On sale!
- Promotion
Soldering tip for soldering station type N1-46 - 2 ZD929C / ZD937
Index: GTK-12275
- On sale!
- Promotion
Raspberry Pi prototyping accesories
Loading...
RTC Battery for Raspberry Pi 5
The Panasonic ML-2020 RTC battery was designed for Raspberry Pi 5 users who want to ensure uninterrupted operation of the real-time clock built into the board, even when the...
Index: RPI-23926
Index: RPI-23926
Connecting cables female-female 60cm - 40pcs
Set includes 40 PCs of colorful connection cables with length of 60 cm, ended, from both sides, with female connector on goldpin.
Index: KAB-03479
Index: KAB-03479
Set of electronic components - E32 - 254 elements
A set of 254 prototype elements for Arduino and Raspberry Pi. Includes: button Tact Switch, LEDs, resistors, potentiometers and goldpin strips. All closed in a small...
Index: GRL-12110
Index: GRL-12110
ProtoPi Plus Side - extension GPIO Raspberry Pi 4/3/2/B for breadboard + tape
The module allows you to connect the GPIO leads of the Raspberry Pi 4, 3, 2 and B plus minicomputer to popular 830-hole contact boards using the included 40-wire tape. The...
Index: MSX-02927
Index: MSX-02927
Set of electronic components - diodes, resistors, buttons
A set of electronic elements required while designing on breadboards. Set includes e.g. resistors, potentiometers and LEDs.
Index: PAS-09910
Index: PAS-09910
Connecting cables female-male 30cm colored - 50pcs
Set of 50 high-quality connecting cables with a length of 30 cm in different colours.
Index: KAB-01438
Index: KAB-01438
OBD-II CAN-BUS Development Kit
OBD-II CAN-BUS Development Kit for Arduino, Raspberry, Beaglebone and other minicomputers, allowing to connect the computer with the vehicle's OBD-II interface and perform...
Index: SEE-14341
Index: SEE-14341
Electronic components set E24 + breadboard 400 - E24 - 235 elements
The set of prototype elements that can be used for creating the systems with Arduino. The kit includes: a breadboard, the power module for the breadboard, sets of wires, Tact...
Index: GRL-12111
Index: GRL-12111
Extension GPIO Raspberry Pi 3/2/B+ to the contact plate + tape
The module allows connection of the GPIO leads of the minicomputer Raspberry Pi 3, 2 and B + to popular breadboards with 830 and 400 holes, using an attached to the set,...
Index: RPI-02892
Index: RPI-02892
MicroSD socket card extender - 15cm - 4pcs - Uctronics U6192
Adapter, microSD card slot extension that can be successfully used with Raspberry Pi minicomputers, 3D printers and other devices. It will work in all devices that require...
Index: ACM-21683
Index: ACM-21683
Cable IDC 40 pin female-female 15 cm Raspberry Pi 4B/3B+/3B/2B
Female cable 15 cm long terminated with 40-pin IDC raster 2.54 mm (goldpin standard) connectors , matching Raspberry Pi 4B / 3B+ / 3B / 2B.
Index: KAB-03618
Index: KAB-03618
ProtoKit prototype kit for Raspberry Pi 4B/3B + / 3B / 2B
The set of prototype elements for the minicomputer Raspberry Pi in versions 4B, 3B+, 3B, 2B, Zero and Zero W. The set includes: breadboard, connection cables, a set of...
Index: GRL-12119
Index: GRL-12119
Cable IDC 40 pin female-female 30 cm Raspberry Pi
Female cable 30 cm long terminated with 40-pin IDC raster 2.54 mm (standard goldpin) connectors , matching Raspberry Pi 4B / 3B+ / 3B / 2B.
Index: KAB-03619
Index: KAB-03619
Cable IDC 40 pin female-female 40 cm Raspberry Pi 4B/3B+/3B/2B
40 cm long female cable terminated with 40-pin IDC raster 2.54 mm (goldpin standard) connectors, matching Raspberry Pi 4B / 3B+ / 3B / 2B.
Index: KAB-02924
Index: KAB-02924
The module enables easy connection of all GPIO Raspberry minicomputer outputs in versions 4, 3, 2 and B+ with any contact plate without the need for soldering. The chip is...
Index: ADA-02781
Index: ADA-02781
MCP23017 module - GPIO pin expander - 16-channel I2C - STEMMA QT / Qwiic - Adafruit 5346
Lead expander from Adafruit equipped with the MCP23017 chip. It allows you to extend the number of pins of modules such as Arduino or Raspberry Pi by an additional 16 I/O...
Index: ADA-21037
Index: ADA-21037
Pogo pins and mounting accessories - for HAT and Raspberry Pi Zero / Zero W - PiMoroni PIM330
Pogo-a-go-go Solderless GPIO Pogo Pins set by PiMoroni . Designed for the Raspberry Pi Zero / Zero W , it allows you to attach the HAT overlay to the module, which has...
Index: PIM-21140
Index: PIM-21140
Camera interface extension kit for Raspberry Pi - ArduCam U6248
The extension kit allows you to replace the FPC ribbon with an Ethernet LAN cable. With its help, you can significantly increase the length of the cable and place the camera...
Index: ACM-21685
Index: ACM-21685
PiCowbell Proto - prototype board for Raspberry Pi Pico - reset button - STEMMA QT - Adafruit 5200
PiCowbell Proto is an extension designed for Raspberry Pi in the Pico version, which enables prototyping of the module and allows you to create electronic circuits yourself....
Index: ADA-22390
Index: ADA-22390
Grove Creator Kit - Gamma - set of 40 Grove modules to Arduino
Set consisting of 40 modules and cables with Grove interface. It has been designed for creators of all ages, regardless of their level of sophistication and experience with...
Index: SEE-15410
Index: SEE-15410
PCF8575 - GPIO pin expander - I2C - STEMMA QT / Qwiic - Adafruit 5611
Adafruit pin expander equipped with PCF8575 chip. It has as many as 16 pins of GPIO inputs / outputs , thanks to which it increases the design possibilities of the modules...
Index: ADA-22192
Index: ADA-22192
Breadboard - 1660 holes with connectors for power supply
Breadboard consists of two small boards containing 830 fields. This version has pins, which allow for connecting and disconnecting the power in a simple and quick way.
Index: PLY-00072
Index: PLY-00072
THT 26pin prototype board with screw connectors for Raspberry Pi
Board allows independent creation of electronic circuits. Connected directly to the GPIO pins of the Raspberry Pi minicomputer. It has soldered screw connections and goldpin...
Index: MOD-05662
Index: MOD-05662
Proto Board for Raspberry Pi Zero
Board allows independent creation of electronic circuits. Connected directly to the GPIO pins of the Raspberry Pi minicomputer in a version Zero.
Index: MSX-05794
Index: MSX-05794
See also
For beginning and experienced DIY enthusiasts, Raspberry Pi prototyping kits
We know that no matter what stage of your Raspberry Pi adventure you are at, you need the right elements and tools to evolve and to be able to implement your ideas and projects. At the prototyping stage, projects are very often tested using contact plates. They allow you to connect components and electrical circuits without using a soldering iron. So it is a very good option to start when you are just learning about Raspberry. They are also chosen by people who are trained in technical subjects. The starter kits are useful for studying electronics, allowing you to put your theoretical knowledge into practice. The kits contain several useful elements. These include LEDs, capacitors, contact plates, wires, resistors, sensors, and integrated circuits. Not only Raspberry Pi, but also other hardware and software platforms, such as Arduino, are used in prototyping. The set is packed in a suitcase, which makes it easy to store accessories as well as to carry them. You can design anywhere.
Why do you need contact plates?
Contact plates are one of the basic project tools used for Raspberry Pi. They are used by experienced designers and are recommended for beginner robotics. They are ideal for virtually any project, both simple and very advanced. The contact plate allows you to create a temporary design of an electronic device, so you can experiment and test the best solutions. Use it for testing to create a final design that perfectly matches your needs and expectations. You can test electronic components such as ICs. The big advantage of the board is the possibility of easy and quick replacement of electronic components, as well as changing the layout of connections. You don't have to use a soldering iron every time, so the project is much easier. This is very important if you are not sure how your circuit will react when you turn on the voltage. Without soldering the connection takes less time and you save time and energy. So the contact plates are great for testing and experimenting with new projects. You can use them to check the behaviour of individual components and replace them with other ones if you think they don't meet your expectations.
You will also find other elements for prototyping the Raspberry Pi. Besides the contact plates you will find cables, GPIO extensions, complete prototype sets and diagnostic modules.
