- Reduced price
- Sale
- Sale
- Sale
List of products by brand OEM - Strona 9
Loading...
LED diode in case SMD 1206 yellow. Price for 10 pieces.
Index: LED-00439
Index: LED-00439
Potentiometer knob GC16 red - 6/16 mm - 5pcs
Knob for rotation potentiometer on axis of 6 mm. The height is 14.6 mm and the outer diameter is 16 mm.
Index: MOD-05736
Index: MOD-05736
Slip ring equipped with 12 wires of 0,8 mm diameter. It is used to transmit power and signals from the stationary component to the rotating component. The diameter of the body...
Index: MOD-07145
Index: MOD-07145
Strip LED SMD5050 IP20 14,4W, 60 LED/m, 10mm, warm white - 5m
LED strip powered by a voltage of 12 V with self-adhesive tape. Consumes power: 14.4 W/m, density of 60 diodes per meter. The color of the light is warm white. Protection...
Index: LED-07084
Index: LED-07084
Index: LED-00231
Quartz resonator 3,579545MHz - HC49- low - 10pcs.
The quartz resonator in the small through hole case.
Index: PAS-01889
Index: PAS-01889
Electromagnet holding 12V 13W 120kgf
Powered by 12 V holding electromagnet, with a maximum load capacity of 120 kg (at standard gravitational acceleration of 9.8 m/s 2 ). The device consumes approximately...
Index: DNG-17582
Index: DNG-17582
Nano Expansion Adapter - Shield for Arduino Nano
System that facilitates the usage of Arduino Nano. It has led out all the pins in convenient 3-pin configurations along with Vcc and GND. On board can also be found pins for...
Index: MOD-08233
Index: MOD-08233
Mini vibration motor 10x3,4mm - 5V
Mini vibration motor powered by 5 V. Module with a diameter of 10 mm and a height of 3.4 mm . Current consumption is 80 mA . The motor module has two wires.
Index: DNG-17923
Index: DNG-17923
Strip LED SMD2835 IP65 4,8W, 60 diod/m, 8mm, warm white - 5m
LED strip powered by a voltage of 12 V with self-adhesive tape. Consumes power: 4.8 W/m, density of 60 diodes per meter. The light color is warm white, protection factor IP20....
Index: LED-05160
Index: LED-05160
A set of 200 resistors with the 1 W power. Elements are in the through hole THT case.
Index: PAS-08281
Index: PAS-08281
Index: LED-11519
Stepper Motor JK57HS76-2804 200 steps/rot 3V / 2,8A / 1,89Nm
JK57HS76-2804 bipolar four-wire stepper motor with 200 steps per revolution (1.8 degrees). It is powered by 3 V, draws 2800 mA per coil. Torque is 19.0 kg*cm (1.89 Nm)....
Index: DNG-14553
Index: DNG-14553
Heat shrink tube 3.2/1.6 red - 10pcs
Diameter before heat shrink: 3.2 mm, diameter after heat shrink: 1.6 mm. Price for 10 x 1 meter.
Index: NSZ-00086
Index: NSZ-00086
Diode Power LED Star 1 W - white with heat sink
Diode Power LED Star 1W with a heat sink. Emits light in a cool white color, close to daylight.
Index: LED-01616
Index: LED-01616
Stepper motor JK42HS40-1704 200 steps 2.8V/1.7A/0.4Nm
Bipolar stepper motor, four wire. It has a resolution of 200 steps per revolution (1.8 degrees). It is powered by 2.8 V and draws 1700 mA per coil. The torque is 4.0 kg*cm (0.4...
Index: MOT-06429
Index: MOT-06429
Aluminum servo mount in size 58 x 37 x 25 mm and weighing 15 g. Suitable for servo MG995.
Index: GRL-10912
Index: GRL-10912
Peltier Cell TEC1-12708 12V / 8A
The cooling cell applied, for example, in portable refrigerators. It is supplied with the voltage up to 12 V, it consumes up to 8 A of current. Board sizes - 40 x 40 x 3.6 mm.
Index: DNG-10020
Index: DNG-10020
Nozzle cleaning needle 1mm - 5 pcs
Needle to clean 3D printer nozzles from the remains of the filament. Dedicated to nozzles of 1 mm diameter . It facilitates the maintenance of the corresponding flow of the...
Index: DNG-17424
Index: DNG-17424
Nozzle cleaning needle 0,35mm - 5 pcs
Flexible needle for cleaning 0.35 mm nozzles used in 3D printers. The product allows you to clear holes clogged with film without damaging the nozzle itself. High...
Index: DNG-17419
Index: DNG-17419
IR Power LED Star 1W - infrared 850nm with heat sink
IR power LED power of 1 watt with heat sink. It emits light in the IR range with a wavelength of 850 nm.
Index: LED-02702
Index: LED-02702
Blades for a knife for processing 3D printouts - deburrer - 10 pieces
Spare deburrer blades , used to process finished models made with a 3D printer. Thanks to its profiled, semicircular shape, it allows you to reach even the most inaccessible...
Index: DNG-17414
Index: DNG-17414
Nozzle cleaning needle 0,6 mm - 5 pcs
Needle for cleaning 3D printer nozzles . Its use allows the nozzle to be kept permeable, thus ensuring the free flow of printing material. The jigsaw designed for nozzles...
Index: DNG-17422
Index: DNG-17422
Index: KAB-00648