Stepper Motor JK57HS76-2804 200 steps/rot 3V / 2,8A / 1,89Nm
Index: DNG-14553
- Reduced price
- Promotion
- On sale!
- Promotion
ELECTRONICS - Strona 56
Loading...
Lanberg Ethernet Patchcord UTP 6 1,5m - blue
Patchcord with a length of 1.5 m in blue color. Cable - twisted pair in category 6 Ethernet with RJ45 connectors installed. It has a cover that protects it from breaking.
Index: IMP-14359
Index: IMP-14359
FORBOT - a powerful 40mm fan for the case for Raspberry Pi 3B/4B
Fan with 5 V input voltage, designed for housing for Raspberry Pi 4/3 from FORBOT. The upper flap and mounting elements are also included.
Index: FOR-14966
Index: FOR-14966
Filament Fiberlogy Easy PETG 1,75mm 0,85kg - Black
Fiberlogy PETG filament in colour black . Vacuum packed with moisture absorber. The product is fully compatible with printers that are not equipped with locks to prevent...
Index: FLA-16085
Index: FLA-16085
- Reduced price
- Promotion
RGB LED Strip WS2812B - digital, addressed - IP65 30 LED / m, 9W / m, 5V - 5m - black
LED bar equipped with individually addressed RGB LEDs with WS2812B chip. The diodes were placed on a 5-meter strip in a density of 30 diodes per meter . Each diode can...
Index: DNG-16607
Index: DNG-16607
IR beam interruption sensor - LED 5mm - 0-25 cm
The motion detection sensor reacts to the interruption of an infrared light beam that is transmitted between the transmitter and receiver . The devices should be placed...
Index: DNG-18688
Index: DNG-18688
Roraty potentiometer 101Ohm linear 1/5W B0.1K/B101 - 5pcs.
The B0.1K/B101 carbon-coated linear rotary potentiometer has three leads that fit on a contactor board. Connected to a microcontroller's analog-to-digital converter (e.g....
Index: DNG-19634
Index: DNG-19634
JustPi THT CF carbon resistor 1/4W 1MΩ - 30pcs.
A set of 30 resistors. The electronic elements are designed for THT through-hole mounting. Resistance is 1 MΩ and tolerance is 5%.
Index: JUS-20017
Index: JUS-20017
USB-UART TTL converter FT232 - USB type C socket - Waveshare 20646
This module is equipped with a converter that allows communication between USB and UART serial interfaces on TTL level. It has built-in FT232 chip and operates with...
Index: WSR-20540
Index: WSR-20540
LoRa Fiberglass 8 dBi, 863-870 MHz RFELA-4/88X - 130cm long - Seeedstudio 318020692
Fiberglass outdoor antenna from Seeedstudio. It works in the frequency range from 863 MHz to 870 MHz and provides an average gain of 8 dBi . The antenna is 130 cm long ....
Index: SEE-21087
Index: SEE-21087
- Reduced price
- Promotion
Noctua NF-A4X20 FLX fan - 40x40x20mm - 3pin.
Advanced premium fan manufactured by Noctua. Its dimensions are 40 x 40 x 20 mm . The NF-A4X20 FLX has been made with the use of advanced aerodynamic technologies - it...
Index: ACT-21654
Index: ACT-21654
Infrared receiver TSOP4838 - 38kHz
IR receiver TSOP4838, it is operating at a frequency of 38 kHz.
Index: SES-01047
Index: SES-01047
Pixel module with addressed RGB LED WS2812B
Module with digital RGB LED WS2812B with the outputs in the form of goldpin raster of 2.54 mm, It allows to obtain any color with a mixture of RGB colors.
Index: MSX-02290
Index: MSX-02290
Module Bluetooth v2.0 + EDR, class 2. It works with a voltage of 3.3 V and communicates over a serial UART interface (RX, TX), supports the AT command. Maximum transmitter...
Index: MOD-02570
Index: MOD-02570
The fan with the input voltage of 12 V, current consumption of 160 mA and dimensions of 60 x 60 x 10 mm.
Index: MOT-03873
Index: MOT-03873
Grove - set of 5 female-female 4-pin - 2mm/50cm with latch
A set of five 4-pin Grove wires. They are used to connect sensors with Grove Base Shield v2. The length of the cable is 50 cm. Version with a latch.
Index: SEE-04399
Index: SEE-04399
Tact Switch 12x12, 7mm THT 6pin - green backlight - 5pcs.
A small monostable button mounted in a through-hole way - THT with six pins with the size: 12x12 mm, height: 7 mm. The button is with the backlight in the green color.
Index: SWT-04786
Index: SWT-04786
Alligator Clips with Wire Female+Male USB Connector
The power cable on the one side, enfed with the USB type-A plug, and on another, with the popular crocodile. It enables the outputting voltage from the USB connector in the...
Index: KAB-05122
Index: KAB-05122
Index: KAB-05351
2-pin male connector housing 2,5mm - 5pcs.
2-pin male connector housing - 2.50 mm raster. In the set there are 5 pieces.
Index: KAB-06305
Index: KAB-06305
10-pin plug for printing, 2.54 mm pitch. Set includes 5 10-pin plugs.
Index: KAB-06770
Index: KAB-06770
The 6-pin plug for printing, the pitch is 2.54 mm. The set includes 5 x 6-pin plugs.
Index: KAB-06772
Index: KAB-06772
Adapter microUSB - DC 5,5/2,1mm angled
The corner adapter enabling the cable connection to the tip 5,5 / 2,1 mm with slot of type of microUSB. It can be used as an adapter to power Arduino and Raspberry Pi.
Index: KAB-07033
Index: KAB-07033
Assembly bar male 4-pin, raster 5,08mm, angular closed
Disconnectable terminal block, male, angled, 4-pin. Raster 5,08 mm. Height 12 mm.
Index: KAB-07130
Index: KAB-07130
Socket DC 5.5 x 2.5 mm with terminal connector - 5pcs
DC φ5.5 x 2.5 mm slot (for AC power supply) with a detachable connector that allows you to mount the cable using a screwdriver.
Index: KAB-07209
Index: KAB-07209