- Reduced price
- Sale
- Sale
- Sale
- Reduced price
- Sale
- Reduced price
- Sale
- Reduced price
- Sale
List of products by brand Seeedstudio - Strona 5
Loading...
Grove - RS-06WD reflectance sensor v1.1
Module from the Grove is equipped with the reflective sensor RS-06WD. It consists of LED emitting the infrared light and phototransistor of high sensitivity. It is supplied...
Index: SEE-11331
Index: SEE-11331
Grove - a set of 5 wires 4-pin 2mm - female wires 2.54mm/30cm
A set of five 4-pin Grove female wires. They are used to connect Grove sensors with a board incompatible with the Grove raster 2.54 mm wires, such as Raspberry Pi. Length is...
Index: SEE-04401
Index: SEE-04401
Module from the Grove series, based on the LM386 system and electret microphone. It can be powered with any voltage from 4 V to 12 V. The output is an analog signal. The sensor...
Index: SEE-11350
Index: SEE-11350
Grove - a speaker with a digital interface
Speaker module Grove is a device controlled by the PWM signal. It c an work as a simple buzzer or audio player. The volume is adjustable with the built in potentiometer. The...
Index: SEE-11352
Index: SEE-11352
Grove - analog NTC temperature sensor
Analog sensor is compatible with Arduino and Raspberry Pi. It is powered with the voltage from 3.3 V to 5 V. It can measure temperature in the range from -40 °C to 125 °C with...
Index: SEE-11356
Index: SEE-11356
Grove - push button with backlight - blue
Module from the Grove is equipped with a button with a blue LED. Powered with the v oltage from 3.3 V to 5 V. It has the Grove connector that allows for the direct...
Index: SEE-13660
Index: SEE-13660
A simple tilt sensor with digital output. It operates from 3.3V to 5V and works with Arduino and Raspberry Pi modules.
Index: SEE-11358
Index: SEE-11358
Grove - Buzzer - module with active buzzer
Active buzzer module from Grove. It e mits a uniform tone after taking a high position. When using PWM, it can generate different sounds and effects. The power voltage from...
Index: SEE-11298
Index: SEE-11298
Grove - IR receiver 38kHz 940nm
IR receiver from Grove , operating at a frequency of 38 kHz with a supply voltage from 3.3 V to 5.0 V. Maximum sensitivity is observed for the wave length of 940 nm.
Index: SEE-04419
Index: SEE-04419
Grove - WS2813 RGB LED Strip Waterproof - 60 LED/m - 1m
Waterproof RGB LED strip powered by 5 volt with replaceable silicone case. It consumes a power of 18 W/m, density is 60 diodes per meter. LEDs can also emit cool white light,...
Index: SEE-13666
Index: SEE-13666
Grove - universal 4-pin angle connector 90° - 10pcs.
Universal 4-pin Grove connector designed to be soldered into PCBs. Raster is 2 mm, the pins are bent at 90°. The connectors are compatible with Grove cables. Set includes 10...
Index: SEE-15452
Index: SEE-15452
Grove - Base Shield v2 - Shield for Arduino
Shield for Arduino, which extends the capabilities I/O pins. Designed for modules and sensors from the Grove series. It has 4-pin connectors, and all the outputs known from...
Index: SEE-04440
Index: SEE-04440
Grove - set of 5 female-female 4-pin - 2mm/50cm with latch
A set of five 4-pin Grove wires. They are used to connect sensors with Grove Base Shield v2. The length of the cable is 50 cm. Version with a latch.
Index: SEE-04399
Index: SEE-04399
Grove - LM358 Ambient Light Sensor v1.2
Module from the Grove series is equipped with a sensor LM358. The sensor allows to determine the intensity of the light and reflects the analog voltage signal back to Arduino....
Index: SEE-11330
Index: SEE-11330
Grove - DS1307 real-time clock I2C
Module from Grove features a real time clock DS1307, which voltage is supplied by a round CR1225 battery (not included) . It allows you to read the time in hours, minutes,...
Index: SEE-13332
Index: SEE-13332
CAN-Bus Shield v2.0 - Shield for Arduino
Shield for Arduino supporting the CAN bus. It is equipped with chips MCP2515 and MCP2551. It communicates via the SPI interface. It works with voltage of 5 V.
Index: SEE-11568
Index: SEE-11568
Grove - MMA7660FC 3-axis digital accelerometer I2C
Module with 3-axis accelerometer based on MMA7660FC chip with digital I2C output and Grove connector. The MEMS sensor has a low power consumption and low profile. The module...
Index: SEE-15444
Index: SEE-15444
Grove - temperature and humidity sensor DHT11 - Seeedstudio 101020011
The sensor of temperature and humidity DHT11 from the Grove series. The output is a digital signal. The temperature measurement range is from 0 °C to 50 °C and...
Index: SEE-12378
Index: SEE-12378
Grove - 10kΩ linear rotary potentiometer - top connector
Potentiometer 10 kOhm with linear rotary. It as a 300° range of rotation. It h as a 4-pin Grove connector on the side of the handle.
Index: SEE-04433
Index: SEE-04433
Grove - LCD display 2x16 characters with backlight (White on Blue)
Monochrome 2 x 16 character LCD display with high brightness backlight from Grove. The module communicates with the control board via the two-row I2C bus. The screen is powered...
Index: SEE-14736
Index: SEE-14736
Grove - a set of 5 wires 4-pin 2mm - male cables 2.54mm/20cm
A set of five wires 4-pin Grove male wires 2.54 mm. They are used to connect Grove sensors with boards incompatible with the Grove raster 2.54 mm wires, for example Arduino.
Index: SEE-04402
Index: SEE-04402
Grove - mini PIR motion sensor
The motion sensor, type PIR with the interface compatible with the Grove series. The object detection is indicated digitally - through the high status on SIG pin. The range of...
Index: SEE-13336
Index: SEE-13336
Grove - universal 4-pin connector
Universal 4-pin connector for soldering in the PCB. The distance between the pins is 2 mm. Compatible with, among others, the wires from the Grove series. The package contains...
Index: SEE-13343
Index: SEE-13343
Grove - sensor / probe for measuring soil moisture v1.4 - analog
The sensor allows you to determine the moisture level of the soil. It is supplied with the voltage from 3.3 V to 5 V. The output has analog voltage, which increases its value...
Index: SEE-11338
Index: SEE-11338