List of products by brand Seeedstudio - Strona 6
Grove - DS1307 real-time clock I2C
Module from Grove features a real time clock DS1307, which voltage is supplied by a round CR1225 battery (not included) . It allows you to read the time in hours, minutes,...CAN-Bus Shield v2.0 - Shield for Arduino
Shield for Arduino supporting the CAN bus. It is equipped with chips MCP2515 and MCP2551. It communicates via the SPI interface. It works with voltage of 5 V.Grove - MMA7660FC 3-axis digital accelerometer I2C
Module with 3-axis accelerometer based on MMA7660FC chip with digital I2C output and Grove connector. The MEMS sensor has a low power consumption and low profile. The module...Grove - temperature and humidity sensor DHT11 - Seeedstudio 101020011
The sensor of temperature and humidity DHT11 from the Grove series. The output is a digital signal. The temperature measurement range is from 0 °C to 50 °C and...Grove - 10kΩ linear rotary potentiometer - top connector
Potentiometer 10 kOhm with linear rotary. It as a 300° range of rotation. It h as a 4-pin Grove connector on the side of the handle.Grove - LCD display 2x16 characters with backlight (White on Blue)
Monochrome 2 x 16 character LCD display with high brightness backlight from Grove. The module communicates with the control board via the two-row I2C bus. The screen is powered...Grove - a set of 5 wires 4-pin 2mm - male cables 2.54mm/20cm
A set of five wires 4-pin Grove male wires 2.54 mm. They are used to connect Grove sensors with boards incompatible with the Grove raster 2.54 mm wires, for example Arduino.Grove - mini PIR motion sensor
The motion sensor, type PIR with the interface compatible with the Grove series. The object detection is indicated digitally - through the high status on SIG pin. The range of...Grove - universal 4-pin connector
Universal 4-pin connector for soldering in the PCB. The distance between the pins is 2 mm. Compatible with, among others, the wires from the Grove series. The package contains...Grove - sensor / probe for measuring soil moisture v1.4 - analog
The sensor allows you to determine the moisture level of the soil. It is supplied with the voltage from 3.3 V to 5 V. The output has analog voltage, which increases its value...Seeeduino Xiao - SAMD21 ARM Cortex M0+ - kompatybilny z Arduino
A small module equipped with an Arduino-compatible SAM2D1G18 ARM Cortex M0+ microcontroller. The board features 14 GPIO connectors , including 11 digital/analog pins, 10...Grove - Module 4x 7-segment display - digital interface
Grove series four-character 7-segment display module. It allows displaying four digits along with colon and some letters in red. Based on TM1637 chip, it is compatible with...Grove - heart rate sensor with a clip on the ear
Set for monitoring the heart rate, contains an ear clip with a wire and receiver module. The results can be displayed on the monitor through a serial port. The supply voltage...Grove - 10kΩ rotary potentiometer linear lower connector
Potentiometer 10 kOhm with linear rotary. It has a 300° range of rotation. It has a 4-pin Grove connector on the other side of the handle. The kit includes a cable adapted...Grove - GrovePi+ v3.0 Shield for RaspberryPi 4/3/2/B/B+/A+
Shield for Raspberry Pi is equipped with a w15 4-pin connectors for connecting sensors from the Grove minicomputer series. It cooperates with more than a hundred modules.Grove - Fan with DC Motor and Controller v.1.1
Fan of soft material, with a DC motor and a controller, based on ATmega168. The board has additional pins, for example for the servo connection.Grove - BME280 - humidity, temperature and pressure sensor 110kPa I2C 3-5V
The Grove module is equipped with a humidity, temperature and pressure sensor powered with the voltage of 3.3 V to 5 V with I2C and SPI interface. Measuring range: temperature:...Grove - 3 Axis Digital Compass V2
Grove Series 3-axis digital compass based on the Bosch BMM150. It allows to measure magnetic field in three perpendicular axes. The data can be read out using the I2C and SPI...Grove - set of 5 female-female 4-pin - 2mm / 40cm with latch
A set containing five 4-pin Grove cables with a clip, 40 cm long. The cables are used to connect the sensors to the Grove connector with the base cover.
