• EOL

Module 3G/GSM - u-GSM shield v2.19 UG95E - for Arduino and Raspberry Pi - u.FL connector

Index: ITB-13923 EAN: 5904422321710

The module allows communication in 3G / GSM standard allows you to make voice calls, send SMS messages. On the board there are: SIM card connector, charging module for Li-Pol / Li-Ion batteries and RESET button. Version works with Arduino, Raspberry Pi and BeagleBone, has connectors for u.FL antennas.

Module 3G/GSM - u-GSM shield v2.19 UG95E - for Arduino and Raspberry Pi - u.FL connector
€74.90
€60.89 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Itbrain Power
Compatibility: Arduino Raspberry Pi

Attention!

The product has been discontinued. Check other products in category.

Product description: 3G/GSM module - u-GSM shield v2.19 UG95E

Module compatible with Arduino, Raspberry Pi (version 3B+, 3B, 2B, B+ and A+) and BeagleBone Black, which enables 3G / GSM communication. It allows to make voice calls and send SMS messages. On the board there are: SIM card connector, charging module for Li-Pol / Li-Ion batteries and RESET button. It has connectors for GSM u.FL antennas.

Moduł 3G/GSM - u-GSM UG95E

Component layout on the u-GSM shield board.

3G/GSM module pinouts - u-GSM shield

Moduł GSM LTE GPRS NB IoT GNSS

Pin Description
STS
Status pinout.
RI Ring Indicator output.
GND System ground.
VCC 4V input/output, internally connected to Li-Pol + pad.
VIN 5V input for Li-Pol charger.
VUSB 5V output.
ENA Activation pin, activated by a high state.
RST Reset, high state activated.
TX Communication via serial interface.
RX . Communication via serial interface.

Connecting 3G/GSM module to Arduino

System works with Arduino Uno using following pins:

Pin Arduino Description
GSM RX D3 Communication via serial interface.
GSM TX D2 Communication via serial interface.
RESET D6 Reset of the GSM chip.
Ena D7 Control voltage of GSM chip (On/Off).
VIN (5 V LiPol) 5 V

5 V power supply. Details of connection in case of LiPol batteries are available in manufacturer's manual.

GND

GND System ground.

STATUS

D5 Status pinout.


Connecting 3G/GSM module to Raspberry Pi

The module has special breakout connectors that allow you to plug directly into the GPIO connectors of your Raspberry Pi or BeagleBone Black.

In order to run the module with Raspberry Pi you need to make the following connections:

Pin RPi Description
GSM RX 10

Communication via serial interface, (not connected for USB communication).

GSM TX 08

Communication via serial interface (not connected when using USB).

RESET 18 GSM system reset.
ON / OFF 16 GSM system power voltage control (On/Off).
VIN (5 V LiPol) 02/04 Supply voltage 5 V.

GND

04/14 GND of the chip.
STATUS 12 Status pinout.

Detailed description of the module can be found in the User Manual in parts one and two and on the manufacturer's website.

3G/GSM module specification - uGSM shield

  • Controller: Quectel UG95E
  • Supported standards: 3G / GSM / UMTS / HSPA
  • Frequencies:
    • UMTS: 900 / 2100 MHz
    • GSM: 900 / 1800 MHz
  • Speeds:
    • HSUPA / HSPDA: up to 5.76 Mbps / 7.2 Mbps
    • UMTS: up to 384 Kbps (DL)
    • EDGE/GPRS: up to max. 296 Kb/s (DL), max. 236.8 Kb/s (UL) / max. 107 Kb/s (DL), max. 85.6 Kb/s (UL)
  • Nano SIM / micro SIM connector
  • Antenna connectors u.FL
  • Built-in USB-UART converter (USB connector can be used to power the module)
  • Automatic selection of logic levels from 3 V to 5 V
  • Reset button
  • Works with Arduino, Raspberry Pi and BeagleBone Black along with manufacturer's sample codes
  • Two mounting holes with diameter: 2.5mm
  • Board dimensions: 45 x 27 mm

Package width 6 cm
Package height 5 cm
Package depth 2 cm
Package weight 0.01 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: