Two-color graphical OLED display 0.96 '' (A) 128x64px SPI/I2C - angled connectors - Waveshare 9085

Index: WSR-04434 EAN: 5904422373962

0.96" OLED display with 128 x 64 px resolution and yellow and blue. The screen based on the SSD1306 controller works with voltages of 3.3 V and 5 V, communicates via SPI or I2C. It has soldered in angled goldpin connectors.

Two-color graphical OLED display 0.96 '' (A) 128x64px SPI/I2C - angled connectors - Waveshare 9085
€7.90
€6.42 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: Waveshare
Compatibility: Arduino

Description: OLED two-colour graphic display 0,96''. (A) 128x64px SPI/I2C- angular connectors

0.96" OLED display with 128 x 64 px resolution, yellow and blue. The screen is based on the SSD1306 controller, works with 3.3 V and 5 V, communicates via SPI or I2C.

This version has soldered-in angled goldpin connectors, in our offer you will also finda display with straight pins.

The manufacturer provides auser guideandlibraries to operate the screen.

Connecting the display

The module has soldered-in angled goldpin connectors - 2.54 mm raster, communicates via SPI or I2C interface. The description of individual outputs can be found in the table.

Pin Symbol Description
1 VCC Supply voltage from 3.3 V to 5.0 V.
2 GND The weight of the system.
3 NC Leave it unconnected.
4 DIN SPI / I2C communication interface data line.
5 CLK Clock line of the SPI / I2C communication interface.
6 CS Selection of the SPI bus device, activated by a low state.
7 D/C Selection of the operating mode - low state means command transfer, high - data transfer.
8 RES System reset, activated in a low state.

Configuration of the module

The communication bus is selected using the jumper BS0 and BS1, which are located on the back of the board. By default, the display works in 4-wire SPI mode. Detailed information can be found in the table below.

Mode

work

Pin

BS0

Pin

BS1

Function

DIN

Function

SCK

3-wire SPI 1 0 MOSI SCLK
4-wire SPI 0 0
I2C 0 1 SDA SC

The jumper for mode selection is located in the middle of the module: BS1 and BS0.

Display specification

  • Operating voltage: 3.3 V to 5.0 V
  • Controller: SSD1306 (documentation)
  • Communication: SPI / I2C
  • Selection of the operation mode using jumper BS0 and BS1
  • Display type: OLED
  • Diagonal: 0,96"
  • Resolution: 128 x 64 px
  • Colours: yellow and blue
  • Viewing angle: over 160°
  • Operating temperature: -20 °C to 70 °C
  • Soldering goldpin connectors - raster 2.54 mm
  • Dimensions: 33.5 x 33 mm

Screen - type OLED
Screen - diagonal 0,96"
Screen - interface SPI+I2C
Screen - touch no
Screen - resolution 128x64px
Test 4
Package width 8 cm
Package height 1 cm
Package depth 12 cm
Package weight 0.007 kg

Piotr

06/27/22

Question: Good day, what is the dimension of the mounting holes in the screen plate?
Answer: The holes have a diameter of 3 mm.
The spacing of the mounting holes (from center to center) is 28 mm.

Customers who bought this product also bought:

Products from the same category: