• EOL

Feather M0 Express 32-bit - in accordance with CircuitPython and Arduino - Adafruit 3403

Index: ADA-09078 EAN: 5904422312459

A small module with a 32-bit microcontroller ATSAMD21G18 ARM Cortex M0+ known from the Arduino Zero, designed for use with CircuitPython, a program that connects Python language with microcontrollers. Feather is designed for portable projects. On board is a microUSB connector, through which the system can be programmed via the Arduino IDE.

Feather M0 Express 32-bit - in accordance with CircuitPython and Arduino - Adafruit 3403
€33.90
€27.56 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Adafruit

Attention!

The product has been discontinued. Check other products in category.

Description

A small module with a 32-bit microcontroller ATSAMD21G18 ARM Cortex M0+, is designed for use with CircuitPython, a program that connects Python with microcontrollers. Feather is designed for portable projects. Thanks to the microUSB connector and uploaded bootloader, the module can be programmed directly fromthe Arduino IDE. Board has a small size (51 x 23 x 8 mm) and can be powered by voltage from USB port or rechargeable battery3,7 V LiPol. The place was left on the board for other elements, such as buttons or sensors.

 

Check out how to start playing with the Adafruit Feather!

 

Mobile projects

Controller Feather is designed for mobile projects. Thanks to the integrated connector, it is possible to power it from the rechargeable LiPol battery 3.7 V. The battery voltage was led through an analog pin, so you can constantly monitor the state of charge of the lipol. Also available is powering from the microUSB port.

 

 

Programming (Arduino IDE)

Feather M0 Express has bootloader UF2. The system is seen as a mass storage, so in order to upload new firmware, just drag the software. There is no need to use additional tools. In this way, you can load programs CircuitPython, PXT MakeCode. The module can be programmed using the Arduino IDE. For this, you will need to configure the software in a way provided by the manufacturer and connect the board using the microUSB cable.The settings of the Arduino IDE are available on the website of the manufacturer.

 

Specification

  • Supply voltage: lipol 3.7 V or USB 5 V slot
  • ATSAMD21G18 ARM Cortex M0+ 3.3 V microcontroller:
    • Flash memory: 256 KB
    • SRAM: 32 KB
    • Clock frequency: internal oscillator 48 MHz
  • Installed Arduino bootloader
  • Works with a modified version of the Arduino IDE
  • ConnectormicroUSBfor programming, in our assortment, you will findthe appropriate wire
  • Installed voltage regulator 3.3 V with current delivery up to 500 mA
  • Power supply from USB port or battery lipol 3.7 V (in our offer, you will findthe appropriate wire)
  • Built-in oscillator 32.768 kHz
  • 20 GPIO pins
  • 20 PWM pins
  • 6 analog inputs
  • 1 x analog output
  • Built-in lipol charging module 100 mA with LED indicator, which informs about the status
  • Led for pin 13
  • The reset button
  • Pins for soldering are included
  • Dimensions: 51 x 23 x 8 mm
  • Weight: approx. 5 g

 

Voltage to 3.3 V
Voltage from 5.0 V
Voltage output from 3.3 V
Output voltage to 3.3 V
Nominal output voltage 3.3 V
UC - Microcontroller ATSAMD21G18
UC - Core 32-bit ARM Cortex M0
UC - Flash 256 kB
UC - RAM 32 kB
UC - core 1. Single Core
UC - Digital pins 20
UC - analog in 6
UC - freq 48 MHz
UC - A/C 12-bit
UC - C/A 1
UC - PWM 20
UC - USB microUSB
UC - I2C yes
UC - UART yes
UC - SPI interface yes
Package width 10 cm
Package height 2 cm
Package depth 3.5 cm
Package weight 0.01 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: